Trouble bleeding clutch SIIa

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
S

Samoth

Member
Posts
46
Can't seem to get the air out of the clutch system. Bleeding at the slave cylinder still leaves me with a peddle that must be triple pumped for effective clutch release. There must be a better a better way. The master cylinder and the slave cylinder have both been replaced. Any ideas will be appreciated!
 
I did redo that. Now it is adjusted so peddle is all the way up with just the 3/4" free play of slave adjustment. The problem is when I pump the peddle enough (2-3 times) for a gear change, then the peddle doesn't hold pressure when my foot is on it and down to the floor.
 
Series 2/2a slaves are vertical @Lee T .
Does sound like you have a duff replacement master and is allowing fluid to return to the reservoir when it should not. That is if it is not leaking out somewhere.
 
Samoth said:
I did redo that. Now it is adjusted so peddle is all the way up with just the 3/4" free play of slave adjustment. The problem is when I pump the peddle enough (2-3 times) for a gear change, then the peddle doesn't hold pressure when my foot is on it and down to the floor.
Click to expand...
How much freeplay on the master push rod?
Is the flex okay?
 
Thanks for the responses! The manual says like 1/16" before the rod contacts the piston. I think it is about negligible now in an attempt to get more peddle travel. Flex hose is new also. I am going to check the master again to see if it will hold after being pumped. If it doesn't, is it trapped air compressing again or a bad master?
 
What make of master cylinder have you bought ?
The ones made in China have a bad reputation for failing straight out of the box.
Having said that, I ran one of them cast iron Britpart m/cylinders on my clutch for 10 years maybe longer
 
No, nothing to do with slave. If pedal still goes down with flexi pinched off it has to be a master issue. [ there is a tool to do this but careful use of a mole grip works.
 
peddle still goes slowly down to floor and can be pumped up sort of ~. Where would be the trapped air?
 
tottot said:
No, nothing to do with slave. If pedal still goes down with flexi pinched off it has to be a master issue. [ there is a tool to do this but careful use of a mole grip works.
Click to expand...
Okay, maybe this is getting somewhere. What is a mole grip and how do I use it?
 
tottot said:
No, nothing to do with slave. If pedal still goes down with flexi pinched off it has to be a master issue. [ there is a tool to do this but careful use of a mole grip works.
Click to expand...
Okay, What is a mole grip and how do I use it? I am using a vise grip plier to clamp off the flex line.
 
It is the same thing, Mole is just the original maker, a bit like hoover for a vacuum cleaner.
Does the pedal still go down all the way now? even slowly.
Oh, just read your first return post. No air, likely fluid passing back to reservoir due to internal fault.
 
tottot said:
It is the same thing, Mole is just the original maker, a bit like hoover for a vacuum cleaner.
Does the pedal still go down all the way now? even slowly.
Oh, just read your first return post. No air, likely fluid passing back to reservoir due to internal fault.
Click to expand...
Pedal goes slowly all the way down.
 
You must log in or register to reply here.

Similar threads

P
Clutch stuck 300 tdi
Replies
12
Views
526
D1Nut
D1Nut
Paul Coddington
P38A 2.5 DT manual Clutch Slave
Replies
6
Views
395
Paul Coddington
Paul Coddington
M
What is the correct way to bleed a series 3 clutch?
Replies
2
Views
2K
tottot
tottot
Lej
Discovery 2 Clutch failure
Replies
2
Views
630
Lej
Lej
MULDERKE
Freelander 1 Sad Tidings. And many Thanks.
Replies
6
Views
780
WhiskyLassie
WhiskyLassie
Back
Top