200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
My mates got a 270 HP RV8 that cost him like 4 grand for the engine
I want More power for less cost
Trailer - challenge truck build
- Thread starter 200tdi ayre
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
My mates got a 270 HP RV8 that cost him like 4 grand for the engine
I want More power for less cost
Thor1950
Well-Known Member
- Posts
- 39,238
- Location
- Land of the midnight sun
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
A Lexus V8 is probably the way I'd go I should think, more refined than any rover or yank V8 plus massive potential
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
Looks like a nice engine. .. love my vvti toyota. What power can you get from it?
250 + non vvti or 1995 engine supercharged nitrous 400hp plus ask zen
I'm 261 hp stock, no cats stock ecu and auto box
Last edited:
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
is that a 3.9 down pipes and y piece the low hanging type??
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
I'm not sure it's what came off the RR it's really right to the transfer box but quite low off the down pipes so I'd think it's low hanging
Mr Noisy
Coming in your ears.
- Posts
- 10,146
- Location
- Altrincham, Cheshire
Yeah the early range had the high Y piece but the later ones with 3.9 were same as discos with the U shaped cross member.
WHEN you fit hedmans jimbo you will need to make ANOTHER crossmember cos then you'll be on high position and you're Y piece will have to go above!
And the you start going through transfer case end front prop UJs like there's no tomorrow cos the grease gets so hot.
Ask me how I know!
WHEN you fit hedmans jimbo you will need to make ANOTHER crossmember cos then you'll be on high position and you're Y piece will have to go above!
And the you start going through transfer case end front prop UJs like there's no tomorrow cos the grease gets so hot.
Ask me how I know!
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Yeah the early range had the high Y piece but the later ones with 3.9 were same as discos with the U shaped cross member.
WHEN you fit hedmans jimbo you will need to make ANOTHER crossmember cos then you'll be on high position and you're Y piece will have to go above!
And the you start going through transfer case end front prop UJs like there's no tomorrow cos the grease gets so hot.
Ask me how I know!
Crossmembers are easy, bitty box and some plates
Headland are soon
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
I was gona say that too
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Better
Seam weld and sort bracketry now
Seam weld and sort bracketry now
defender11069
AKA Mr cool...
- Posts
- 8,616
- Location
- up sh*t creek with out a paddle
Better
Seam weld and sort bracketry now
looking good now get on with it and get it finished
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Note to self .... Wear welding gloves
Picking up an exhaust on the weld you just welded tends to hurt quite a lot
Picking up an exhaust on the weld you just welded tends to hurt quite a lot
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
been there! lol. looking good!
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Top hose air bleed just a 10mm nut a short bolt and a copper washer and it's sorted
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
Good lad
Similar threads
