KillaJoules
Active Member
- Posts
- 950
- Location
- West Herts
Dunno how Fred and Barney managed it but that's a heavy bugger to paddle around. That said I bet all the tyres are flat again eh stu
Tinkering with my Vogue
- Thread starter stutab
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
stutab
Well-Known Member
- Posts
- 3,285
- Location
- Hemel Hempstead, Hertfordshire
Only one is flat. Still need to retrieve the compressor.
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
Joules I think I was in front of you other morning some moron missed the road closed sign at Dagnall and went around the roundabout in front of a nice shiny 110!
KillaJoules
Active Member
- Posts
- 950
- Location
- West Herts
Couldn't be me, mined filthy 😁
Quite likely, though I have gone through Gaddesden and over the beacon twice this week
Quite likely, though I have gone through Gaddesden and over the beacon twice this week
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
You must have a secret polishing mop!!
Next comp is mid month who is going?
Next comp is mid month who is going?
KillaJoules
Active Member
- Posts
- 950
- Location
- West Herts
Hopefully, got nicely replaced door pillar now. Just need to create a new rear exhaust bracket as it's rested away
KillaJoules
Active Member
- Posts
- 950
- Location
- West Herts
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
Sweet!!
Stu I bet driving Lees 90 felt huge to drive about vs the series 1!
I not a member of CVLRC yet...... But 90 needs a new rear propshaft, 300 tdi is longer oops!! front diff and ends swap roof rack off and odds n soda will be at Brickhill taking part in December.
Stu I bet driving Lees 90 felt huge to drive about vs the series 1!
I not a member of CVLRC yet...... But 90 needs a new rear propshaft, 300 tdi is longer oops!! front diff and ends swap roof rack off and odds n soda will be at Brickhill taking part in December.
KillaJoules
Active Member
- Posts
- 950
- Location
- West Herts
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
Just a bracket don't loose the fixing dingocroft all parts genuine cost Neely £60! Rubber spacers nuts bolts and side plates!
KillaJoules
Active Member
- Posts
- 950
- Location
- West Herts
No the hanger assembly is new just like the s11 back box. However I also need to bend the pipe a bit to get it away from the wheel so the 7.50s ultimatly can go on.
Where the hanger fit on the tailpipe required a heath robinson extension bracket from the chassis to fit.
probably come out by 6cm and drop by 4cm. the photos are of where the top of the rubber is after I have forced the tailpipe back.
Originally it was a piece of bent steel which has finally fatigued/rusted away at the fold.
Where the hanger fit on the tailpipe required a heath robinson extension bracket from the chassis to fit.
probably come out by 6cm and drop by 4cm. the photos are of where the top of the rubber is after I have forced the tailpipe back.
Originally it was a piece of bent steel which has finally fatigued/rusted away at the fold.
stutab
Well-Known Member
- Posts
- 3,285
- Location
- Hemel Hempstead, Hertfordshire
Bring it up will concoct something
stutab
Well-Known Member
- Posts
- 3,285
- Location
- Hemel Hempstead, Hertfordshire
Tinker Time 
op2:
Thought I would crack on with the fuel tank today, had to figure out how to hold the tank while figuring out the brackets.
Found out that the front bracket was snagging on the tank, so I cut it off :cool2:
Time to test the wax coating I bought
Says spray on with airless sprayer, but goes on well with a brush
So tank in, belly plate on, now to figure out what I have got to make something with. Any Ideas welcome
Cant leave it like this
Pondering over that I decided to do the oil on the gearbox and transfer box and change the breathers so I can bolt the floor back down
That done I made the clutch pipe up before I filled the engine bay with all of the bits.
Just need to fix it to the bulkhead, slow but sure progress.
Helping Killajoules get his 88" home tomorrow then hopefully back on the Rangy :crazy_driver:
op2:Thought I would crack on with the fuel tank today, had to figure out how to hold the tank while figuring out the brackets.
Found out that the front bracket was snagging on the tank, so I cut it off :cool2:
Time to test the wax coating I bought
Says spray on with airless sprayer, but goes on well with a brush
So tank in, belly plate on, now to figure out what I have got to make something with. Any Ideas welcome
Cant leave it like this
Pondering over that I decided to do the oil on the gearbox and transfer box and change the breathers so I can bolt the floor back down
That done I made the clutch pipe up before I filled the engine bay with all of the bits.
Just need to fix it to the bulkhead, slow but sure progress.
Helping Killajoules get his 88" home tomorrow then hopefully back on the Rangy :crazy_driver:
Last edited:
stutab
Well-Known Member
- Posts
- 3,285
- Location
- Hemel Hempstead, Hertfordshire
Between recovering Killajoules's latest member of the family (SWAMBO's 88) we found some time, after lunch to try and put the ancillary bit's onto the V8.
Trying to fit parts from two engines isn't working. And there will only be one alternator but which we don't know
After some head scratching we called it a day as we had to decapitate the 88 and put it away
Trying to fit parts from two engines isn't working. And there will only be one alternator but which we don't know
After some head scratching we called it a day as we had to decapitate the 88 and put it away
stutab
Well-Known Member
- Posts
- 3,285
- Location
- Hemel Hempstead, Hertfordshire
Went to collect the winnings from eBay, 2 front wings 2 front doors a rear door and set of gas struts, didn't want the change from my tenner get the other door and rear wings if the buyer is a no show.
Bit more head scratching and decided to strip the remaining engine ancillaries off the V8 from the se. Just need a new power steering hose made up now and that's another job ticked off the list.
get the other door and rear wings if the buyer is a no show.Bit more head scratching and decided to strip the remaining engine ancillaries off the V8 from the se. Just need a new power steering hose made up now and that's another job ticked off the list.
Rustystuff
Active Member
- Posts
- 237
Hi Stu... just wondering if the Range you were breaking is still about ? I'm looking for a brake booster unit for mine.
Cheers.
Cheers.
stutab
Well-Known Member
- Posts
- 3,285
- Location
- Hemel Hempstead, Hertfordshire
Ye. Still got some bits. What year is yours as I have 2 spare. I'm after a manual pedal box if you know of any.
Rustystuff
Active Member
- Posts
- 237
Thanks Stu... Mines a 92. Don't have any spares of that nature myself... but will be seeing a fella on Friday who might ? Will ask him.
stutab
Well-Known Member
- Posts
- 3,285
- Location
- Hemel Hempstead, Hertfordshire
Ok cheers.
stutab
Well-Known Member
- Posts
- 3,285
- Location
- Hemel Hempstead, Hertfordshire
I have a 91 on the Rangy. I will compare it to my spare ones and see if they are the same. Would you want it sent or pick it up?
Similar threads
