Disco 2 This is where the Oil Filter is?!

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Deanod

Deanod

Member
Posts
46
Location
Cornwall, UK
This is a little thing that I expect everyone to already be familiar with, but I'm still a Disco newbie...

While getting to water pump (turns out not water pump but Power Steering rot on shaft) I had to take off the turbo. Underneath the exhaust manifold I found the oil filter. I get that you could get to the Centrifugal filter without the Turbo off but the normal filter looks pretty difficult to get at.

Is this really the only way to get to the Oil Filter?! Do you really have to take off the turbo every time?
IMG_6407.JPEG

I'm getting a Service Pack from Bearmach a little later tonight but is there anything else I should get to work on while it's in bits?

Deano
 
Deanod said:
This is a little thing that I expect everyone to already be familiar with, but I'm still a Disco newbie...

While getting to water pump (turns out not water pump but Power Steering rot on shaft) I had to take off the turbo. Underneath the exhaust manifold I found the oil filter. I get that you could get to the Centrifugal filter without the Turbo off but the normal filter looks pretty difficult to get at.

Is this really the only way to get to the Oil Filter?! Do you really have to take off the turbo every time?
View attachment 227326
I'm getting a Service Pack from Bearmach a little later tonight but is there anything else I should get to work on while it's in bits?

Deano
Click to expand...

No.. there is a oil filter spanner for the td5 filter check paddocks site for one.
 
When you put the new one on only do it up hand tight, and NEXT time you come to take it off, put a pair of rubber gloves on and loosen it when the engine is still COLD, then warm up the engine. The filter will come off with your hands in gloves. Put a small plastic bag like a dog pooh bag around the filter to catch as much spilled oil as poss. It ain't impossible, just takes a bit of practice!:):):)
 
Stanleysteamer said:
When you put the new one on only do it up hand tight, and NEXT time you come to take it off, put a pair of rubber gloves on and loosen it when the engine is still COLD, then warm up the engine. The filter will come off with your hands in gloves. Put a small plastic bag like a dog pooh bag around the filter to catch as much spilled oil as poss. It ain't impossible, just takes a bit of practice!:):):)
Click to expand...
+1 it's not difficult unless you've got huge hands
 
Henry_b said:
Nah one of these.

31BE7cvD5JL._AC_SX355_.jpg


A 'tard must of chosen the placement for the filter on the TD5.

Engineers don't ask mechanics!!!!
Click to expand...
Have used all sorts in the past including a weird thing that attaches to a 1/2" breaker bar, prefer a strap wrench with a rubber type strap. but i only ever need one once as I do the job properly and can use rubber gloves from then on!
 
I remove the oil cartridge filter by hand, not exactly a cinch, but you can get your hand in there relatively easily from above (unless your hands are like monster mitts!) to remove it and also put the new one on - never use a spanner or strap and never had leaks at the filters. Takes less than 5 minutes to remove and replace, making sure seal isn't left behind and new seal is lubricated.
 
I use an oil spanner - it's simple, cheap and although it's a Britpart (DA1117), it does work and is still in one piece !

Also, go easy with the bolts for the centrifugal filter cover as they are know to strip the threads on the housing.
 
NPG said:
I use an oil spanner - it's simple, cheap and although it's a Britpart (DA1117), it does work and is still in one piece !

Also, go easy with the bolts for the centrifugal filter cover as they are know to strip the threads on the housing.
Click to expand...
Noted! I have been really going to town with WD40 before touching anything recently.

Actually I've got a method for stuck stuff but i've never run it past anyone. Loads of oil about an hour before, if it doesn't come easy, paint stripper gun to warm everything up and then a big old breaker bar, used slowly.

I've found that massive overkill, used gently, breaks less bolts than using a small spanner with violence. Or am I just way off the mark?
 
NPG said:
I use an oil spanner - it's simple, cheap and although it's a Britpart (DA1117), it does work and is still in one piece !
Click to expand...
I have this as well but never used as it fits only for one type of filter (maybe for genuine or Britpart?).
I use this type, works well for me.
upload_2021-1-10_16-42-12.png
 
You must log in or register to reply here.

Similar threads

MAF Diver
Disco 2 Unknown coolant leak at the front onto the oil filter and diff
Replies
0
Views
216
MAF Diver
MAF Diver
PopPops
Disco 2 TD5 Mahle oil filter
Replies
4
Views
301
PopPops
PopPops
S
WIF sensor wire 12v
Replies
0
Views
130
sgagroundworks
S
Arctic2
Freelander 1 Grey Smoke
2
Replies
31
Views
1K
Arctic2
Arctic2
D
Disco 2 td5 fuel purging doesn't work?
Replies
10
Views
586
Kev12
Kev12
Back
Top