think i cooked my 300tdi

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Dids said:
Finally, an answer rather than just saying it's the head with no reason. I still don't think it is the head on the vehicle in question though which isn't a td5 either. May I add this is my personal opinion and I'm more than willing to be proven wrong.
Click to expand...

I think we can rule a cracked fuel rail out on it anyway.;):D:D:D

On the grounds the op stated the following earlier on in he thread

it is possible ive done upwards of 1000 miles with about a litre of water .i realised , toped up and bled .. it then boiled itself followed by steaming like a kettle frm exhaust along with black sooty water . being in the middle of now wer ,in the middle of the night and BEIN A **** i decided to try and drive home 50miles . water ran out , running fine temp fine(obviuosly air temp) .
so basically it run fine until you add water ?
Click to expand...

My money is still on melted piston/s.
 
midnite moocha said:
150 miles and still ok , looking at a new lump i think , if i had melted piston , how would this affect coolant and let it into cylinder ?
Click to expand...

If it got hot enough to start melting a piston it's hard to say what other damage could be done without seeing the engine. Was there any scoring to the bores or movement on the pistons?

What make was the HG that you fitted? Did you fit it the right way up?
 
ok the enevitable happened and the temporary fix has now give up .
managed 2 days bak to work ,200mile
so im bak to deciding the fate of this motor .
i dnt have much money left now and im a bit stuck .
im confident in the head gasket and fitting but how can i diagnose head/block /problem? is it worth further investigation ?
 
midnite moocha said:
ok the enevitable happened and the temporary fix has now give up .
managed 2 days bak to work ,200mile
so im bak to deciding the fate of this motor .
i dnt have much money left now and im a bit stuck .
im confident in the head gasket and fitting but how can i diagnose head/block /problem? is it worth further investigation ?
Click to expand...

Are the symptoms the same as before you took the head off?
 
nrgserv said:
no gasses comin out?
you wont see oil or water as it'll be a vapour.
should be able to feel it tho.
run till warm with rad cap on.

if its clear, i'll try an think of summat else.
Click to expand...
ok ive tried this and there is no sign of any vapour ,
runs ok with no cap on exp tank.
as soon as u screw down cap , the pressure builds and within seconds its steamin . no signs of any sort of leakage anywer round head gasket.
may be of interest , wen warm even tho thres prob less 8 litres coolant in , the tank stays full until u massage pipes then it emptys like some blockage or air lock happens with stat in or out ( open /closed )
 
unfortunately got all signs of head / gasket.

my course of action now would be to remove head and have a closer inspection of the cylinder liners, possibly get head pressure tested again at a different place.

decide then as to where to go next.
 
nrgserv said:
unfortunately got all signs of head / gasket.

my course of action now would be to remove head and have a closer inspection of the cylinder liners, possibly get head pressure tested again at a different place.

decide then as to where to go next.
Click to expand...


Not the Helicoils then ?
 
You must log in or register to reply here.

Similar threads

Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
755
Padda.116
Padda.116
roule
OIl pump priming issue
Replies
11
Views
2K
roule
roule
G
300Tdi coolant issue
Replies
2
Views
579
GilesHarrison
G
A
P38A Head Gasket Kit & ARP Bolts ?
2
Replies
23
Views
1K
enjoi
enjoi
Rich W
Disco 2 TD5 camshaft rotation torque
Replies
5
Views
662
Rich W
Rich W
Back
Top