- Posts
- 83,266
- Location
- Embasinga stocæ
Last edited:
The resurrection of Tufftee - Part Deux :o
- Thread starter The Mad Hat Man
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 9,105
- Location
- Roaming the UK on assignments
- Posts
- 9,105
- Location
- Roaming the UK on assignments
So where are we up to?
How did you get on with the wheels?
How did you get on with the wheels?
- Posts
- 83,266
- Location
- Embasinga stocæ
Getting there - all sorted
- Posts
- 83,266
- Location
- Embasinga stocæ
He moves .
Admittedly not under its own steam, but it saw sunshine again today.
Not sure replacement tyres are any better than those removed, but can pump them up when necessary
.Admittedly not under its own steam, but it saw sunshine again today.
Not sure replacement tyres are any better than those removed, but can pump them up when necessary
- Posts
- 83,266
- Location
- Embasinga stocæ
first evenings work finished.... no pics, but more rot found.
Removed dash and cut away the inside of the Nearside A pillar. Job for the week is to clean up the inside of the A Pillar to see how bad it is. Also cut bulkhead to suit new panel.
Removed dash and cut away the inside of the Nearside A pillar. Job for the week is to clean up the inside of the A Pillar to see how bad it is. Also cut bulkhead to suit new panel.
- Posts
- 9,105
- Location
- Roaming the UK on assignments
I took some pictures
Dash out.
Big arze hole in the footwell and bulkhead.
We had a go with pneumatic nibbler.
I found a guy wielding an angle grinder in anger too
Door post with a chalk line for cutting.
Top corner of the bulkhead from the outside where the three panels meet, a real haven for the tin worms.
Also discovered a little more attention is required on the drivers side sill.
Sadly it has to get worse before it gets better
Bit of luck next week we can commence with the welding hey MHM
Dash out.
Big arze hole in the footwell and bulkhead.
We had a go with pneumatic nibbler.
I found a guy wielding an angle grinder in anger too
Door post with a chalk line for cutting.
Top corner of the bulkhead from the outside where the three panels meet, a real haven for the tin worms.
Also discovered a little more attention is required on the drivers side sill.
Sadly it has to get worse before it gets better
Bit of luck next week we can commence with the welding hey MHM
Attachments
- Posts
- 83,266
- Location
- Embasinga stocæ
Pity he couldn’t keep to the blinking lineI found a guy wielding an angle grinder in anger too
View attachment 149765
Door post with a chalk line for cutting.
View attachment 149768
Bit of luck next week we can commence with the welding hey MHM
.Might need to tidy it up
Last edited:
- Posts
- 9,105
- Location
- Roaming the UK on assignments
Pityhecouldnt keep to the blinking line
Might need to tidy it up
No stress, lines are only guides, new panels cut to suit
Did you get all excited and get that 75mm air cut off tool?
Oh and how was the belly buster burger?
- Posts
- 83,266
- Location
- Embasinga stocæ
Ordered the cut off tool.
No burger as at Mary Rose at the mo.
No burger as at Mary Rose at the mo.
- Posts
- 83,266
- Location
- Embasinga stocæ
gess where we iz?
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
In a car park?
- Posts
- 83,266
- Location
- Embasinga stocæ
Well. That as well .
Now we iz doing battlements and Napoleon pows
.Now we iz doing battlements and Napoleon pows
- Posts
- 9,105
- Location
- Roaming the UK on assignments
Nice, super place to visit isn't it
Burgers are top notch and he's open 24/7
I remember the Mary Rose being brought up from the depths when I was a kid, it was rather exciting stuff back then
I was looking at air power shears today and I'll see if I can get one for Friday, it should make preparing new steel easier, cleaner and safer as there are no sparks.
Burgers are top notch and he's open 24/7
I remember the Mary Rose being brought up from the depths when I was a kid, it was rather exciting stuff back then
I was looking at air power shears today and I'll see if I can get one for Friday, it should make preparing new steel easier, cleaner and safer as there are no sparks.
- Posts
- 83,266
- Location
- Embasinga stocæ
Most of those cutters are rated for 1.2mm, occasionally 1.6mm steel. Can’t see anything better.
- Posts
- 83,266
- Location
- Embasinga stocæ
Started drilling out spot welds on the D2 slam panel, to remove the crap left over from its removal.
refitted the tow bar cap to my tow bar
refitted the tow bar cap to my tow bar
- Posts
- 9,105
- Location
- Roaming the UK on assignments
That's my trouble at the mo, trying to find something that will do 16G (roughly 1.5mm) sheet, most of them are rated up to 18G which is roughly 1.1mm, it has to do 1.2 with ease not as a maximum ideally.
- Posts
- 83,266
- Location
- Embasinga stocæ
well....... i tried today, but it is steady rain, so a little bit of cutting and derusting carried out. Thats about it
.
Last edited:
- Posts
- 83,266
- Location
- Embasinga stocæ
so am IYou weren't joking - that's some project! Glad your getting some help with it though. It'll all be worthwhile
