She's dead

WeeChris · Jul 29, 2016

That's maybe an exaggeration

Battery connected.

Key fob locking and unlocking door.

Dash lights on

Usual window reset messages & altenator fault appeared.

Turn key you hear a click under dash but no engine turning.

All looks fine at starter etc

Is there something I'm missing with electronics

Chris

ovalandrover · Jul 29, 2016

Starter motor burnt out

WeeChris · Jul 29, 2016

Starter was ok before engine change..

Had it out and tested with jump leads and battery all ok.

Was wondering if it could be something electronic

Pete The Biker · Jul 29, 2016

Bad/missing earth connection?

Pete

Enuff · Jul 29, 2016

A small wire attached to your starter by crappy spade connector may be the culprit if wet and covered in mud and cow sh1t.
It's the starter motor 'trigger'.

kurtjohnson10 · Jul 29, 2016

Hopefully she can be revived

martyuk · Jul 30, 2016

Any other messages on the dash?

WeeChris · Aug 14, 2016

Got her turning over but can't get her to start.

Key fob works ok to unlock doors.

The alarm/immobiliser red light on top of dash doesn't work.

Was thinking maybe immobiliser is on.

Would engine still turn over if it was on?

If I used EKA code would this switch off immobiliser?

Say my code was 1 2 3 4

For code is it with door locked 4 left the 1 left, 2 right, 3 left & 4 right?

Grrrrrr · Aug 14, 2016

Sounds like it might have gone out of sync. EKA won't help there. Need diag.

wammers · Aug 14, 2016

WeeChris said:
Got her turning over but can't get her to start.

Key fob works ok to unlock doors.

The alarm/immobiliser red light on top of dash doesn't work.

Was thinking maybe immobiliser is on.

Would engine still turn over if it was on?

If I used EKA code would this switch off immobiliser?

Say my code was 1 2 3 4

For code is it with door locked 4 left the 1 left, 2 right, 3 left & 4 right?

If engine is immobilised you will get a message on dash. "Enter EKA code or press fob". If it is out of sync no message is displayed. What car Diesel petrol?

WeeChris · Aug 14, 2016

It's. Dse

wammers · Aug 14, 2016

WeeChris said:
It's. Dse

If there are no dash messages and it turns over but does not start it could well be out of sync. You will need the use of a diesel Syncmate or a Nanocom to sort it out. The security code in the engine ECM needs to be written to the BECM. Have you changed the engine ECU?

martyuk · Aug 14, 2016

WeeChris said:
Got her turning over but can't get her to start.

Key fob works ok to unlock doors.

The alarm/immobiliser red light on top of dash doesn't work.

Was thinking maybe immobiliser is on.

Would engine still turn over if it was on?

If I used EKA code would this switch off immobiliser?

Say my code was 1 2 3 4

For code is it with door locked 4 left the 1 left, 2 right, 3 left & 4 right?

If It's turning over then it won't be an EKA Problem. As mentioned it's more likely to be a sync issue, that a Syncmate or Nanocom will sort out.

For reference, EKA is entered by turning 4x to LOCK, then 1st digit to Unlock, 2nd to Lock, 3rd to Unlock, 4th to Lock, and then one final turn to Unlock.
The final turn to Unlock should then unlock the rest of the doors, and allow the vehicle to be started.

WeeChris · Aug 15, 2016

Ok, without spending a fortune can anyone recommend where to get a an mate or similar.

Or even better anyone around the Edinburgh on the forum got one I can borrow or rent one from.

I live close to forth road bridge.

My mate has a Snsp On Solus?

https://www1.snapon.com/diagnostics/us/SOLUSUltra

Would this work.

Thanks

wammers · Aug 15, 2016

WeeChris said:
Ok, without spending a fortune can anyone recommend where to get a an mate or similar.

Or even better anyone around the Edinburgh on the forum got one I can borrow or rent one from.

I live close to forth road bridge.

My mate has a Snsp On Solus?

https://www1.snapon.com/diagnostics/us/SOLUSUltra

Would this work.

Thanks

Would not think so. You could try. But a diesel Syncmate or Nanocom will certainly do it.

martyuk · Aug 15, 2016

Not sure about the Snap On tool, but I'm guessing it probably won't communicate with the BECM to write the code in.

I have Syncmates for hire for all 3 engine types. £35 including postage (RM 1st Class signed) plus £50 deposit which is refunded when it's returned. Drop me a PM if that's any help.

Marty

WeeChris · Aug 15, 2016

Finding any mates online for £150.

That sound about right?

Hoping to try borrow one from someone !!

WeeChris · Aug 15, 2016

Marty where you based?

If no one local has one I'll be right back to you?

I go on holiday week on Wednesday. So ideally like to be done before hols or just after.

martyuk · Aug 15, 2016

I'm based in swindon, but have sent them out all over the country before, they usually show up next-day.

I go away on Sunday 21st for work and am not back home until about the 21st September, but am about this week to send out if needed.

Cheers,
Marty.

WeeChris · Aug 15, 2016

Ok

Will get back to you asap

She's dead

Member

Well-Known Member

Member

Active Member

Well-Known Member

Well-Known Member

Well-Known Member

Member

Technician, Bodgit & Scarper Ltd

No longer with us, RIP

Member

No longer with us, RIP

Well-Known Member

Member

No longer with us, RIP

Well-Known Member

Member

Member

Well-Known Member

Member

Similar threads