Series 3 109 1/2 chassis !

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Jason2

Jason2

Well-Known Member
Posts
2,001
Location
Poitou Charentes-France
Hi
I'm currently stripping down a 1977 series 3 109 to do a full renovation job and am looking for a rear 1/2 chassis but can't find one ???

I can find loads of SWB half chassis but none for the 109 ?? I'm a dab hand with a welder so does anybody know if a SWB can be used/modified to fit a 109 ????

Thanks in advance
 
The one on ebay is for a series 1 if its the same one and looks like somebody's made it in their shed by the looks of the welds, and 1250 quid!!! its not even galvanised..
I don't think you will find one for a series 3 109.
 
Rodeo Joe said:
The one on ebay is for a series 1 if its the same one and looks like somebody's made it in their shed by the looks of the welds, and 1250 quid!!! its not even galvanised..
I don't think you will find one for a series 3 109.
Click to expand...

Oh yeh ! Just seen that ! You can get a SWB one for about £300, I'm sure I will be able to modifie it to fit ! What could be wrong ? too short I can make it longer and chop off old fuel tank supports and re-use ! what else
 
Chopz said:
What do you mean?
I've just looked again at the one on eBay,it looks good or I'm I missing something?
Click to expand...
It does look good ! But that's a 1/4 chassis but still better than nothing. My original post was for a 1/2 chassis for a 109, you can get them for SWB but not the 109 ? Was just saying that going off the photos the 109 has an extra crossmember in between the chassis rails as appose to the SWB .
 
Ok
I think the spring hangers are different as well
When I did the rear chassis on my 109 the 1/4 chassis was enough but I still had to replace the front spring hangers as well as some lower middle chassis sections
 
Chopz said:
Ok
I think the spring hangers are different as well
When I did the rear chassis on my 109 the 1/4 chassis was enough but I still had to replace the front spring hangers as well as some lower middle chassis sections
Click to expand...

Ok Cheers mate . Having already priced up spring hangers, rear out riggers etc I just thought that a new 1/2 chassis would have been the way to go . Looks like it’s going to be a 1/4 chassis then and just cut out all the rotten bits and weld .

Cheers Jason
 
LWB and SWB chassis are very different, especially at the rear. Get a 1/4 chassis and the rear outriggers. You can get chassis rail repair bottom sections. Is your mil or civvy? Very important as the rear crossmembers, outriggers and spring hangers are different in ways that matter.
 
rob1miles said:
LWB and SWB chassis are very different, especially at the rear. Get a 1/4 chassis and the rear outriggers. You can get chassis rail repair bottom sections. Is your mil or civvy? Very important as the rear crossmembers, outriggers and spring hangers are different in ways that matter.
Click to expand...

Thanks for that ! It's a civvy station wagon !
 
You must log in or register to reply here.

Similar threads

C
Truck cab fitting help
Replies
10
Views
554
Chonker
C
IDK...
Engine oil series 3
Replies
19
Views
2K
kermit_rr
kermit_rr
S
Series 3 gearbox in Series 1
Replies
8
Views
700
Hicap phill
H
DeanDS
Series 3 SWB 200TDI cambelt change
Replies
6
Views
773
lynall
L
series 3
Charge light on series 3
Replies
7
Views
761
grewth
G
Back
Top