Rebuilding my 90

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
I bent it several times until got it right, its well away from the dash and my unfinished dash comes back a few inches. The length is ok, great for resting arm on and gives an easy silky change rather than the chunky disco change. I have experimented with different dash designs and this one is nearly there.
l intend to convert the box to defender spec, l have the top off my original box and just need the conversion bits, gear lever will be same but other way around. : )
 
landowner said:
I bent it several times until got it right, its well away from the dash and my unfinished dash comes back a few inches. The length is ok, great for resting arm on and gives an easy silky change rather than the chunky disco change. I have experimented with different dash designs and this one is nearly there.
l intend to convert the box to defender spec, l have the top off my original box and just need the conversion bits, gear lever will be same but other way around. : )
Click to expand...
Not a bad idea. I don't think it'd help with mine unless it's possible to convert it to side to side like a puma but I bet it's a completely diffirent box for them.
Need to put a seat and chubby box in and see where ya hand sits like and position to that. Everything had been a bit of a mare today all jobs that's dead easy with two people but finger trapping sweary jobs without haha
 
small update ,,,,,,,,,,,,,nowt much done of late (skint) lol .but managed to make a stand alone wiring harness for the heater done away with trying to incorporate 300tdi two speed loom into 3 speed heater resistor and switch ,now it just needs to pic up an earth and ignition feed ,happy days
 
Starting to look like a Land Rover
 

Attachments

  • IMG_0409.JPG
    IMG_0409.JPG
    275.8 KB · Views: 276
  • IMG_0403.JPG
    IMG_0403.JPG
    218.9 KB · Views: 281
  • IMG_0403.JPG
    IMG_0403.JPG
    218.9 KB · Views: 275
  • IMG_0410.JPG
    IMG_0410.JPG
    321 KB · Views: 275
no total bugger about:eek: but worth it i think ,,,helped that my wings are plastic so super glue and baking soda filled gaps ,lol
 
GATSO said:
no total bugger about:eek: but worth it i think ,,,helped that my wings are plastic so super glue and baking soda filled gaps ,lol
Click to expand...
Definitely worth it for me, I think they look great. Gives an updated feel without being OTT. Do you think they would neatly fettle in to a ali wing?
 
easier on ally but you will have to have both blank wings has the traditional vent is too deep to be covered by the disco vent
 
Looks awesome can't wait to see it finished so I can steal some more ideas... :p if I remember right was it you who moved your air filter to the bulkhead? If so how did you attach it I'm thinking of doing the same :)
 
only air filter I've moved was when i built my lightweight and utilised the tool box on the nearside inner wing :D:D
 
Few pictures slowly slowly catchy monkey last picture now that's a run Biafra falls
 

Attachments

  • IMG_0449.JPG
    IMG_0449.JPG
    141.9 KB · Views: 239
You must log in or register to reply here.

Similar threads

B
R380 Oil Pump Torques.
Replies
2
Views
141
Brumagem
B
R
LT77 gearbox Wanted
Replies
1
Views
242
julianf
julianf
Defender90 ged
Help needed
Replies
0
Views
215
Defender90 ged
Defender90 ged
A
S3 Brake warning light
Replies
2
Views
225
steve2286w
steve2286w
D
Diff switch
Replies
2
Views
303
donsdilema
D
Back
Top