Range Rover Classic with A Chevy V8

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Syncmaster710n

Syncmaster710n

New Member
Posts
5
Location
United Kingdom
Hi All, am new to this forum but was on LRO before it shutdown.

Anyway so i have a 6.0L Chevy LQ4 V8 and a Auto box that it came with (4L80E i think) that i am looking to put in a Range Rover Classic. I have recently bought a 93 RRC that had been sat for 18 years. Thinking of using a LT230 bolted up to the Auto box with an adapter (have seen a few available online) and then just need to sort out the axles.

I will keep this forum updated with my progress but it will probably take a while as there is a lot involved on this project.
IMG_20180628_115622_resized_20180630_044400868.jpg
 

Attachments

  • IMG_20180318_102157_resized_20180630_044343507.jpg
    IMG_20180318_102157_resized_20180630_044343507.jpg
    353.7 KB · Views: 161
I'd be concerned at the structural condition of a classic that's been standing for so long, is such a momentous project viable?
 
Kev12 said:
mechanically its the same, only differences will be if yours is a soft dash
Click to expand...
Its a hard dash but it has the 200 TDi that is not covered in the Haynes manual, but that doesn't matter as I am going to replace the engine. So as long as the rest is the same thats fine.
Thanks
Sam
 
norseman said:
I'd be concerned at the structural condition of a classic that's been standing for so long, is such a momentous project viable?
Click to expand...
It does have rust in places but I will fix it up, my plan is to get the body off and see how the chassis is, if it comes to it i could replace the chassis. The worst rust is on the tailgate but that seems to be common on these.
 
Syncmaster710n said:
It does have rust in places but I will fix it up, my plan is to get the body off and see how the chassis is, if it comes to it i could replace the chassis. The worst rust is on the tailgate but that seems to be common on these.
Click to expand...

wait till you see the sills, footwells, boot floor and side panels, inner wheel arches and rear cross member. maybe the A and B pillar bottoms.. but aside from that.... should be sound
 
I think @zen has been here before but I don't think he has logged in in ages. Not since the forum changed, now I think about it. His old threads must be on here somewhere though. Sure he dropped a 6l lump in a Classic once.
 
I would have thought the shear weight of an iron V8 sitting on the front suspension would be the biggest drawback, as regards the handling characteristics.
 
Overfinch fitted the 350 small block and it was known as the 570I and it had no issues whatsoever.
They also fitted a 6.3 383ci v8 in later hard dash classics.

Even the P38 got the GM treatment with a 300+hp 6.3 known as the 630r!!


The classics had a 700r4 4spd, which i believe is closely related to the GM turbo 400

As for fitting i imagine it wouldn't be too difficult but as the above have said the structure of the car will have to be assessed first.

The Wiring might also be a mare to do..
 
You must log in or register to reply here.

Similar threads

F
1980 Range Rover 2 door v8 to 300tdi
2
Replies
20
Views
2K
Grrrrrr
Grrrrrr
Muji
P38A Please help me find a steering wheel hub and adapter for my 99 Range Rover P38.
Replies
4
Views
161
pwood999
pwood999
TimoTS
Range Rover classic 3.9EFI no oil visible under oil fill cap.
Replies
19
Views
427
aj1954
aj1954
M
Looking for A/C Wiring Diagram (1992-1994 Range Rover Classic)
Replies
0
Views
393
mikerrc1992
M
T
Auto Box Wont stay in Gear
Replies
11
Views
592
Graculus
Graculus
Back
Top