Project Rusty.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
That didn't go according to plan :(

22:30 =

IMG_20200719_224427.jpg


PAS pump seized solid, snappy snappy goes the belt, nowhere safe to pull in an she got a little warm, not hot, I hope :eek:

Shoe laces saved the day :)
 
That didn't go according to plan :(

22:30 =

View attachment 215126

PAS pump seized solid, snappy snappy goes the belt, nowhere safe to pull in an she got a little warm, not hot, I hope :eek:

Shoe laces saved the day :)

Can't tell you just how much I hate that setup on the 200Tdi. Has to be the one thing that whoever that was in charge of designing this excellent engine had a brain fart on.
Attempt to power anything that draws anything above average amps and the alternators start eating those small belts for breakfast.

Don't know if its something you would want to consider, but electric power steering pumps from say an old saxo work a treat....they only work when required and don't really require any special modifications aside probably having your hoses extended.
And should they fail, doesn't take out your water pump drive.
Next course of action then would be to machine a hub with the stock PAS drive pulley to bolt to the back plate that held the pump, retaining your existing belt and tensioning setup.

Too much?
I have a workshop with all the toys and weekends can get boring sometimes.:D
 
Can't tell you just how much I hate that setup on the 200Tdi. Has to be the one thing that whoever that was in charge of designing this excellent engine had a brain fart on.
Attempt to power anything that draws anything above average amps and the alternators start eating those small belts for breakfast.

Don't know if its something you would want to consider, but electric power steering pumps from say an old saxo work a treat....they only work when required and don't really require any special modifications aside probably having your hoses extended.
And should they fail, doesn't take out your water pump drive.
Next course of action then would be to machine a hub with the stock PAS drive pulley to bolt to the back plate that held the pump, retaining your existing belt and tensioning setup.

Too much?
I have a workshop with all the toys and weekends can get boring sometimes.:D
One of the reasons I fitted my second alternator, it has a heavier duty drive belt direct off the crank pulley.

I did think about electric after seeing how good the Peugeot system was on my old 307.
 
I have done no work on the Landrover since the lockdown started in March. The vehicle is in an open fronted shed. The wind blows in dust. The pigeons roost in the roof and crap... I don't mind those so much, what annoys the Hell out of me is someone who's kicked in the door of a nearby portakabin, found a tin of spray paint and then come and tagged the offside front wing.
 

Attachments

  • IMG_1129.jpg
    IMG_1129.jpg
    292.7 KB · Views: 180
I have done no work on the Landrover since the lockdown started in March. The vehicle is in an open fronted shed. The wind blows in dust. The pigeons roost in the roof and crap... I don't mind those so much, what annoys the Hell out of me is someone who's kicked in the door of a nearby portakabin, found a tin of spray paint and then come and tagged the offside front wing.

Shame it weren't Banksy, you could have swapped wings out and been quids in ...
 
@Kiwi Jim you should start your own thread mate. Not only is this one dedicated to rusty, it also means you can document your work and pick up advice from members on here.
If you type @ prior to their username, you can tag them in your post :)
 
@Kiwi Jim you should start your own thread mate. Not only is this one dedicated to rusty, it also means you can document your work and pick up advice from members on here.
If you type @ prior to their username, you can tag them in your post :)
Thanks for the advice. I shall do that. What put me off doing that was the prospect of posting into the void, with me the only follower of the thread.

Apologies for invading Rusty's thread.
 
Thanks for the advice. I shall do that. What put me off doing that was the prospect of posting into the void, with me the only follower of the thread.

Apologies for invading Rusty's thread.

There will be plenty following, we all like to believe we're not alone in our endeavours ...
 
Thanks for the advice. I shall do that. What put me off doing that was the prospect of posting into the void, with me the only follower of the thread.

Apologies for invading Rusty's thread.

Wasn’t a dig at all mate, just know your doing the same stuff that we are all doing so definitely worth keeping a log of it all.
We all love a resto project and you’ll get advice from here like I have from people who have done the job in had 10 times over.
We will follow and certainly be able to share.
 
Wasn’t a dig at all mate, just know your doing the same stuff that we are all doing so definitely worth keeping a log of it all.
We all love a resto project and you’ll get advice from here like I have from people who have done the job in had 10 times over.
We will follow and certainly be able to share.
Not at all. I am happy to be put right when I've inadvertently infringed good manners on this site. My experience of setting up a new thread to discuss how to weld went nowhere, so my expectations were low. But you've now told me how to bring such a tread to the attention of others, for that I'm grateful.
 
Well, it's not moved in months, not even bothered to try starting it since it was hastily replaced with a Ford Maverick after blowing up the gearboxes, really need to speak to James about my gearboxes but life and work are getting in the way perpetually.
Taxi ride home.

IMG_20200926_162623.jpg


Replacement motor sourced in a hurry.

IMG_20200927_153756.jpg


Updates on my progress to follow, slowly.....
 
Welcome back @dieseldog69

at least a Ford gives you weekends back
Yeah but it lacks that bond I had with my Discovery :(

Nice to see you back was thinking the other day not seen you here...Merry Christmas and a Good New Year to you and all...

Merry Christmas and a happy new year to you too :)

Life, work, lock downs and lack of a Land Rover (could mention the far leftism of the forum too :rolleyes:) means I don't have as much time as I once had and nothing much to say, good job I skipped the BLM garbage, I have strong views that don't align with anti British international communists ;)
 
Back
Top