- Posts
- 83,279
- Location
- Embasinga stocæ
£££££?
Project Rusty.
- Thread starter dieseldog69
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 9,105
- Location
- Roaming the UK on assignments
- Posts
- 83,279
- Location
- Embasinga stocæ
- Posts
- 9,105
- Location
- Roaming the UK on assignments
for a clamp?
Erm, no, sorry, was in my own world again
ESAB welding jacket was £65
DIN socket was £7
DIN plugs were £9
2X0.8mm wire £12
So by deduction that made the clamp £13, really can't complain at that as it is of such good quality
- Posts
- 83,279
- Location
- Embasinga stocæ
Ah - you decided on a welding jacket then?
Shimsteriom
Master Procrastinator
- Posts
- 41,905
- Location
- Over Here
Soon to be a smoking jacketAh - you decided on a welding jacket then?
- Posts
- 9,105
- Location
- Roaming the UK on assignments
Ah - you decided on a welding jacket then?
Saw how snazzy you looked in yours last night and I couldn't resist
Soon to be a smoking jacket
Vaping jacket my good man, well, unless I set myself afire
Not yet
But I did decide that a new set of thermal overalls was in order to keep me warm whilst I play welders outside LOLZ
Santa had better bring something nice, I've been a really good boy
- Posts
- 83,279
- Location
- Embasinga stocæ
But I did decide that a new set of thermal overalls was in order to keep me warm whilst I play welders outside LOLZ
Santa had better bring something nice, I've been a really good boy
https://www.ebay.co.uk/itm/Sacobel-...m=323418085821&_trksid=p2045573.c100505.m3226
- Posts
- 9,105
- Location
- Roaming the UK on assignments
I went with Dickies flame retardant ones, they came in extra fat for no extra cost LOLZ
- Posts
- 83,279
- Location
- Embasinga stocæ
yo buffday pressie should be here by friday,,,,,, forgot to change del addrI went with Dickies flame retardant ones, they came in extra fat for no extra cost LOLZ
- Posts
- 9,105
- Location
- Roaming the UK on assignments
yo buffday pressie should be here by friday,,,,,, forgot to change del addr
You shouldn't have
- Posts
- 83,279
- Location
- Embasinga stocæ
i know.......You shouldn't have
https://www.ebay.co.uk/itm/HI-VIS-D...8343f40f3:m:mAe4cpNR4wEgaJ8u3TDDLqA:rk:1:pf:0
- Posts
- 9,105
- Location
- Roaming the UK on assignments
Well I did all my chores today, leaf blowing, shopping and cooked dinner so I will be outside all day tomorrow and hope that I can get the sill finished, floor plated out, boot floor and side plates stripped out and half way ready for the new wheel tub and floor side on the drivers side in.
I would like to get a bit more plating out done on the rear quarter but will have to see how time goes!!!
I would like to get a bit more plating out done on the rear quarter but will have to see how time goes!!!
- Posts
- 83,279
- Location
- Embasinga stocæ
ear! wot about this to protect yo heres?
https://www.ebay.co.uk/itm/Flame-Re...363b45ef:m:mLOvuZHRaPSbTOnn5cXm1mg:rk:12:pf:0
https://www.ebay.co.uk/itm/Flame-Re...363b45ef:m:mLOvuZHRaPSbTOnn5cXm1mg:rk:12:pf:0
- Posts
- 9,105
- Location
- Roaming the UK on assignments
Send some motivation this direction please
- Posts
- 9,105
- Location
- Roaming the UK on assignments
Gets heavy going sometimes doesn't it
My primary motivation is the fact that I have not been out green laning in months
I'd really like to get it done so that I can get out at least one more time before Christmas Weather looks good for tomoz so you should be out there nailing it harder than a 16yr old in a brothel
1988smithy
Well-Known Member
- Posts
- 4,044
- Location
- West midlands
I know but I got up crack of dawn this morn go go wet my rod as it had been too long
I'm going to take dog on long run in morn and go for a propper coffee. Hopefully I'll get some time. The welder hasn't been out for a while.
Axle looks good though worst comes to worst I'll fit the remaining hub, diff and shafts. Very mindful how heavy it's getting now lol
I'm going to take dog on long run in morn and go for a propper coffee. Hopefully I'll get some time. The welder hasn't been out for a while
.Axle looks good though
worst comes to worst I'll fit the remaining hub, diff and shafts. Very mindful how heavy it's getting now lolSimilar threads
