Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
:hysterically_laughi:hysterically_laughiLike itAt least it's given Virgin trains a dry run if the jocks vote for independence. They stopped all their trains at Carlisle today.
P38 to L322 Bonnet
- Thread starter Mongo
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
SnowmanV8
Well-Known Member
- Posts
- 3,938
- Location
- Portishead, Near Bristol
Pop into the gaylander section that's more like a hairdressers! I will have to warn you though the doors did fall off so they run around other areas a bit atm!
- Posts
- 58,170
- Location
- Preston Lancs.
- Posts
- 16,479
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
:lalala:
odyssey
Active Member
- Posts
- 364
- Location
- Derbyshire
While I tend towards the purist persuasion, this:- Range Rover P38 HSE 4.6 / LPG L322 Full conversion | eBay is one of the best I've seen, it's seems to have been done very neatly, the bonnet looks properly shut, unlike most.
Don't like the wheels at all, and it would look better with the lettering, but that's just me. Can't work out if he means there's an inside switch for the tailgate or you have to crawl in and push something . . .
Don't like the wheels at all, and it would look better with the lettering, but that's just me. Can't work out if he means there's an inside switch for the tailgate or you have to crawl in and push something . . .
- Posts
- 16,479
Whilst the workmanship of the conversion is good, it is the proportions of the vehicle just look wrong in my eyes....the tail looks too stumpy (yes the L322 has a big arse end but this looks too short and stumpy) the gap under the bonnet edge albeit even, is to large....etc...
A good work on the conversion though....aesthetically it looks wrong!
That does look ok, but i think this one looks a tad better...
RANGE ROVER LPG PETROL 4.6 P 38 HSE L322 CONVERSION | eBay
Just not sure about the bonnet, as the front lower lip above the tops of the headlights don't look right... nothing major, just not how or what it should be.
- Posts
- 58,170
- Location
- Preston Lancs.
300AJC
New Member
- Posts
- 931
- Location
- Chelveston, Northants
Steady on Sir, nothing wrong with my Gaylander.
I hope you you have split ends for the rest of your life!
300AJC
New Member
- Posts
- 931
- Location
- Chelveston, Northants
I should have kept my p38. I had friends then. :Cry:
That is why people with sense don't change them.
There's some sort of insult in them there big fancy word things ya usin sonny huh:behindsofa:
And what is this Gaylander quest you speak of Snowman??? find it i can not:monitor_punch:
- Posts
- 16,479
Gaylander = Freelander
Its a Land Rover for da wiminz...
The doors to the Freelander section here have broken letting them run amok over the rest of the forum, they particularly like coming into the Range Rover section just so they can catch a glimpse of something to aspire too....
Its a Land Rover for da wiminz...
The doors to the Freelander section here have broken letting them run amok over the rest of the forum, they particularly like coming into the Range Rover section just so they can catch a glimpse of something to aspire too....
- Posts
- 58,170
- Location
- Preston Lancs.
Gaylander = Freelander
Its a Land Rover for da wiminz...
The doors to the Freelander section here have broken letting them run amok over the rest of the forum, they particularly like coming into the Range Rover section just so they can catch a glimpse of something to aspire too....
This a statement of utter fact and cannot be denied.
- Posts
- 16,479
Bingo was his name-o
gfromleeds
Well-Known Member
- Posts
- 2,234
- Location
- leeds. westyorkshire, uk
Its a bit like going out with a fat lass...
Its a fun ride till your mates find out then its a life of **** take till you get rid...
Its a fun ride till your mates find out then its a life of **** take till you get rid...
Last edited:
anorakmark
Active Member
- Posts
- 329
- Location
- Kent
Tony, It's easy, you just need a junior hacksaw & gaffa tape, let me know how you get on :hijacked:Thinking of modifying mine for a retro look. How easy would it be to fit a series one bonnet and grille?
