- Posts
- 22,904
- Location
- In the next Glen
Not a bobtail a 6x6
- Thread starter pierreblonde
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 12,628
- Location
- Sud ouest France !
Holy fricking jésus. What à build
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
Ch
CheersAwesome I love this. Good job sir.
Hicap phill
Well-Known Member
- Posts
- 16,242
- Location
- Wiltshire
Quick Q on the rose joints...
Do they have to be clamped both sides?( u shaped bracket)
Or would this prevent more articulation.
im glad you are a fabricator this work is nice
& well researched
Do they have to be clamped both sides?( u shaped bracket)
Or would this prevent more articulation.
im glad you are a fabricator this work is nice
& well researched
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
Yes they nip up tight on the ball and the carrier moves freely around that. These are m22 ones from McGill motorsport I bought the spacers for them on the axle to pack them out. They aren’t expensive. And I turned some to suit the existing mounts where the A frame would go
6pot
Well-Known Member
- Posts
- 704
- Location
- Depends...
Brilliant project and some fantastic fabrication you are doing there, will look forward to further progress.
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
Well I’ve sorted the last prop out. Got a 1480 series yoke and shortened the stock disco rear. Tacked it up in place using
a DTI and mag mount. Seams ok but might get it balanced yet. I’ve still got some nee trailing arms to make. Im going to use bushes on the axle side and Johnny joints on the other. Any thoughts?? Front prop is still off it but took it for it’s first run in the street. I’m Pretty please! I need to knock the pump back a bit like. Here’s a short **** video . It’s the only way I could do it
a DTI and mag mount. Seams ok but might get it balanced yet. I’ve still got some nee trailing arms to make. Im going to use bushes on the axle side and Johnny joints on the other. Any thoughts?? Front prop is still off it but took it for it’s first run in the street. I’m Pretty please! I need to knock the pump back a bit like. Here’s a short **** video . It’s the only way I could do it
- Posts
- 12,628
- Location
- Sud ouest France !
Hicap phill
Well-Known Member
- Posts
- 16,242
- Location
- Wiltshire
Keep the suspension arms the same with Jonny joints each end. Nothing will impeded the axle movement.
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
I was thinking that. But I think I read somewhere just to put them on one end. I was thinking also about putting a rose joint on the axle end and a Johnny joint on the chassis end. But I had a look about and there wasn’t much on a setup like that
Hicap phill
Well-Known Member
- Posts
- 16,242
- Location
- Wiltshire
30 years ago that racer ran rose joints front & rear only for ease of swapping. They do make a noise though when they have a slight wear. (This motor would do less than 20 miles a year on road for mot purposes)
Things may have progressed on reliability
- Posts
- 225
- Location
- Blyth Northumberland
Nice work fella, great see how you worked thru the problems.
Mega build so far
Ian
Mega build so far
Ian
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
I’m on fitting the wings up before I paint them. I thought I’d have ago at making extended wheel arches rather than bolt on ones. I’m intending the change the discos category from M1 to N1 llight goods. The rules for the IVA are different for N1. M1 the arch has to cover the tyre. N1 it has to cover just the rim . If I’m reading it right. Has anyone any experience if that’s correct thanks
Last edited:
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
Few updates and pick your brains. Biuld is coming on. Slow going but I altered the winch bumper that I’ve had on her for years. The body need a 50mm body lift to give more clearance for the other transfer box. So the was a gap from the bump top to the grill. And I had to extend the width. Finished it in raptor paint. In on building the flat bed. I’ve fitted the old winch from the front , under the bed on the back the made some a removable panel as I wanted it hidden. I’ll take it all back of when it’s fitted up right a raptor pair it to match the front. Making a stainless steel water tank to fit between the body rails as I’m intending to Build a demountable camp body for it. Got the cab interior nearly done fitted an android screen on the dash for sat nav , phone etc, just got rear glass to get, some to trims to do for the back panel and recover the seats
and this is a I presume vacuum hose to a switch on the heater box behind the dash. I can’t remember where the hell it went or even if it was connected. The heater works fine. There is a tee on the vacuum pipe to the brake servo but it’s was always blocked off
and this is a I presume vacuum hose to a switch on the heater box behind the dash. I can’t remember where the hell it went or even if it was connected. The heater works fine. There is a tee on the vacuum pipe to the brake servo but it’s was always blocked off
- Posts
- 12,628
- Location
- Sud ouest France !
Vacuum for the Egr valve maybe?
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
No it’s a 200tdi so hasn’t got one
Zed.
Well-Known Member
- Posts
- 1,842
- Location
- Deepest Bandit country (Wales)
for the heaters recirculation, vacuum powers an actuator via a solenoid on the top / side of the heaterbox
tee'd near the servo & hose runs across bulkhead & enters cabin near wiring iirc...
edit, went out to get photo's...
feeds through bottom right....
Rich.
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
Cheers , there is a tee there just the leg looks like it has a plug in it. I’ll connect it up. Thanks againfor the heaters recirculation, vacuum powers an actuator via a solenoid on the top / side of the heaterbox
tee'd near the servo & hose runs across bulkhead & enters cabin near wiring iirc...
edit, went out to get photo's...
feeds through bottom right....
Rich.
pierreblonde
Active Member
- Posts
- 58
- Location
- consett
Well it took a tad long than I was thinking but she’s done and on the road now. The IVA was nowhere near as bad as I’d thought. Failed the first time on a few bits but passed the week after. It got issued a new ViN and ended up on a Q plate, I’d have like to keep its original plate. But such is life. Running it as a flatbed but I’m building a demountable camper body for it. That’s not far away from being done now. I’ll give it a good shake down tho before I head off camping in it
Attachments
doriz
Well-Known Member
- Posts
- 17,312
That’s immense.
