nanocom unit

Ianwallace · Jan 16, 2015

hi guys
I've just received my new nanocom unit
the only thing is.

how does this bloody thing work

I bought this unit to clear a message that pops up every time I put the key in

alarm fault

does anyone have one of these units
or know what buttons to press to get rid of this
message

thanks in advance

Datatek · Jan 16, 2015

You could try reading the instructions.

Ianwallace · Jan 16, 2015

ar yes you would think so

there is nothing in the box
and I cant find a dam thing on line

biggeeeee · Jan 16, 2015

Documentation - NANOCOM Evolution

Ianwallace · Jan 16, 2015

biggeeeee said:
Documentation - NANOCOM Evolution

I've looked on hear and I can't find a bloody thing

biggeeeee · Jan 16, 2015

Do you have your unlock code?

wammers · Jan 16, 2015

Home Page - NANOCOM Evolution

dashwoodlandy · Jan 16, 2015

Hi Ian

Funnily enough I received my Nanocom today also, the instructions should be a single sheet of paper listing the setup procedure at the bottom of the box.

The link to that page is here
http://www.nanocom-diagnostics.com/uploads/downloads/Quick%20Setup%20Guide%20V1.25.pdf

The first thing you need to do is plug in the USB power lead into a laptop and the unit will power up

Press Nanocom Diagnostic
Wait for the unit to load software
You will see a list of cars and some green arrows at the bottom, press the right hand side green button
You will see a Nanocom button...press it
press setup
press nano com ID
You will see the units unique ID number, make note of it exactly as it shows up
Then go to
Register - NANOCOM Evolution
and register your unit

You will then have to wait for an email confirming your registration and password

There will be a link in the email that will let you login

When you login you will see your unique unit licences (unlock codes)
You will see the unlock codes button below the noncom ID button on the unit
Enter your unlock codes into the relevant section so my P38 codes needed to be entered into unlock7 and unlock8

Once you have entered your codes you are ready to use the nano com in your car.

Remember that you can't access the Becm with the engine running, but as far as I know you can access everything else with the engine running.

hope this helps

Ianwallace · Jan 16, 2015

dashwoodlandy said:
Hi Ian

Funnily enough I received my Nanocom today also, the instructions should be a single sheet of paper listing the setup procedure at the bottom of the box.

The link to that page is here
http://www.nanocom-diagnostics.com/uploads/downloads/Quick%20Setup%20Guide%20V1.25.pdf

The first thing you need to do is plug in the USB power lead into a laptop and the unit will power up

Press Nanocom Diagnostic
Wait for the unit to load software
You will see a list of cars and some green arrows at the bottom, press the right hand side green button
You will see a Nanocom button...press it
press setup
press nano com ID
You will see the units unique ID number, make note of it exactly as it shows up
Then go to
Register - NANOCOM Evolution
and register your unit

You will then have to wait for an email confirming your registration and password

There will be a link in the email that will let you login

When you login you will see your unique unit licences (unlock codes)
You will see the unlock codes button below the noncom ID button on the unit
Enter your unlock codes into the relevant section so my P38 codes needed to be entered into unlock7 and unlock8

Once you have entered your codes you are ready to use the nano com in your car.

Remember that you can access the Becm with the engine running, but as far as I know you can access everything else with the engine running.

hope this helps

Hi there
Yes I've set the unit up ok
But I can't find away to reset this alarm fault message that I have
Every thing on line is not very clear
I don't want to start pressing buttons and causing more damage

dashwoodlandy · Jan 16, 2015

PS

I used a cut down Iphone 4 (4s) screen protector on the Nanocom screen for a bit of peace of mind, fitted spot on.

wammers · Jan 16, 2015

dashwoodlandy said:
Hi Ian

Funnily enough I received my Nanocom today also, the instructions should be a single sheet of paper listing the setup procedure at the bottom of the box.

The link to that page is here
http://www.nanocom-diagnostics.com/uploads/downloads/Quick%20Setup%20Guide%20V1.25.pdf

The first thing you need to do is plug in the USB power lead into a laptop and the unit will power up

Press Nanocom Diagnostic
Wait for the unit to load software
You will see a list of cars and some green arrows at the bottom, press the right hand side green button
You will see a Nanocom button...press it
press setup
press nano com ID
You will see the units unique ID number, make note of it exactly as it shows up
Then go to
Register - NANOCOM Evolution
and register your unit

You will then have to wait for an email confirming your registration and password

There will be a link in the email that will let you login

When you login you will see your unique unit licences (unlock codes)
You will see the unlock codes button below the noncom ID button on the unit
Enter your unlock codes into the relevant section so my P38 codes needed to be entered into unlock7 and unlock8

Once you have entered your codes you are ready to use the nano com in your car.

Remember that you can't access the Becm with the engine running, but as far as I know you can access everything else with the engine running.

hope this helps

Edited.

dashwoodlandy · Jan 16, 2015

What if any fault codes is the nano com reporting?

wammers · Jan 16, 2015

dashwoodlandy said:
What if any fault codes is the nano com reporting?

Bit premature he hasn't found out how to switch it on yet.

dashwoodlandy · Jan 16, 2015

Have a look here, search is your friend

http://www.landyzone.co.uk/lz/f10/p38-alarm-fault-message-48058.html

wammers · Jan 16, 2015

dashwoodlandy said:
Have a look here, search is your friend

http://www.landyzone.co.uk/lz/f10/p38-alarm-fault-message-48058.html

Alarm fault message is also triggered by system failing it's self check five consecutive times, ultrasonic unit usually causes this. Think he has changed the ultrasonic unit unless i am getting mixed with another thread, but may need diag to cancel fault stored in ECU.

dashwoodlandy · Jan 16, 2015

Wammers

Thanks for editing my stupid error Can should be can't, hours of fun for someone having read that post!!

I have edited my post accordingly

wammers · Jan 16, 2015

dashwoodlandy said:
Hammers

Thanks for editing my stupid error Can should be can't, hours of fun for someone having read that post!!

I have edited my post accordingly

Now can you edit my name and get it right.

dashwoodlandy · Jan 16, 2015

Just off to get my eyes tested, byeee

wammers · Jan 16, 2015

dashwoodlandy said:
Just off to get my eyes tested, byeee

:hysterically_laughi:hysterically_laughi

Ianwallace · Jan 16, 2015

Hi guys
I have registered the unit and I've put in the two codes that are showing on my account

I have replaced the sensor inside the car

But I just don't know how to use this nanocom unit to reset the message

I dont want to start pressing buttons for the fun of it and buggering things up.

Me things I want my trooper back

nanocom unit

Active Member

Well-Known Member

Active Member

Retired - Living the dream

Active Member

Retired - Living the dream

No longer with us, RIP

Member

Active Member

Member

No longer with us, RIP

Member

No longer with us, RIP

Member

No longer with us, RIP

Member

No longer with us, RIP

Member

No longer with us, RIP

Active Member

Similar threads