Nanocom evo vehicle type verication failed

Grit Valve · Feb 17, 2016

Hi all just purchased nano of a chap on here
It's got motortronic installed
Plug it in all worked apart from above
Any ideas please before I email
Nanocom
I have registered the device today
Do I need a new code for it to work on mine? thought they work on all p38,s with the right engine ie gems or edc or motortronic
Mine is 2000 4.6 banana inlet motortronic yes?its been a while sorry
So what's up ??? Please

Grit Valve · Feb 17, 2016

OK I been reading the nanocom motronic page and I found this

Please note that in the Nanocom Evolution the software looks to the presence of the Body

Control ECU to know whether connected to a Discovery II or a P38 model. Unless you have

the unlock code for the relevant Body Control module the system will report a verification

failed message. so is this my car unlock code or nanocom unlock code confused ???

wammers · Feb 17, 2016

Motronic for what? If it's for a motronic Disco with a blue cable plug it won't work, the P38 uses an OBDII cable with a green plug. Disco uses a cable with a blue plug. If it's from a Disco think you will need the unlock code for the Motronic P38. They do work on all P38s but you have to have the correct unlock code and the correct cable.

pwood999 · Feb 17, 2016

If you haven't already, then join the Nanocom Forums here http://nanocom.blackbox-solutions.com/index.php/forum

They are quite helpful, and can check your device codes, etc. Once you have a login, you can access the update area to download latest software, plus access the register codes for your device.

Grit Valve · Feb 17, 2016

Ok was bought with p38 motortronic wammers has green lead I have registerd and
I have checked the unlock codes with my id on the nanocom website in block 5 and 8 all is good including correct upper and lower case letters
I do like the new improved website

I'm just updating firmware as I type this
Other than that I'm clueless ???

pwood999 · Feb 17, 2016

Maybe check the diagnostic connector for corrosion ?

Grit Valve · Feb 17, 2016

pwood999 said:
Maybe check the diagnostic connector for corrosion ?

Yes when my update iis done I will do the nanocom lead test sure I saw this in the menu

Thanks

wammers · Feb 17, 2016

Grit Valve said:
Ok was bought with p38 motortronic wammers has green lead I have registerd and
I have checked the unlock codes with my id on the nanocom website in block 5 and 8 all is good including correct upper and lower case letters
I do like the new improved website
I'm just updating firmware as I type this
Other than that I'm clueless ???

Have you run the pin test?

Grit Valve · Feb 17, 2016

wammers said:
Have you run the pin test?

No not as yet as all was working, BUT

Just done update and low and behold all is in working order no faults anywhere apart from blower Motor current
Could be worse thanks chaps
Phew !!!!
Cheers all

wammers · Feb 17, 2016

Grit Valve said:
No not as yet as all was working, BUT
Just done update and low and behold all is in working order no faults anywhere apart from blower Motor current
Could be worse thanks chaps
Phew !!!!
Cheers all

Well i'll be blowed.

Nanocom evo vehicle type verication failed

Grit Valve

2000 4.6 Vouge

Grit Valve

2000 4.6 Vouge

wammers

No longer with us, RIP

pwood999

Well-Known Member

Grit Valve

2000 4.6 Vouge

pwood999

Well-Known Member

Grit Valve

2000 4.6 Vouge

wammers

No longer with us, RIP

Grit Valve

2000 4.6 Vouge

wammers

No longer with us, RIP

Similar threads