- Posts
- 58,170
- Location
- Preston Lancs.
Then look to Keiths scenario. The Nanocom is sometimes to cleaver for it's own good and will have you chasing shadows. At what period in it's operation is the engine doing 33 RPM?
Nanocom analysis - EDC fuelling
- Thread starter Grrrrrr
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Then look to Keiths scenario. The Nanocom is sometimes to cleaver for it's own good and will have you chasing shadows. At what period in it's operation is the engine doing 33 RPM?
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
Try setting cruise, shut down the Nanocom and the BECM, then go and change it back to Not Set. Sometimes there can be strange outputs from memory chips, re-writing the info can cure it.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
That's what I figured, hence why I've always ignored it in the past. 
I think this is where I came in!
I think this is where I came in!
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
OK. Will give it a go when I get back. I kind of assumed it happened to everyone without cruise control or maybe without and with lowline BECM.
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
That is also a possibility, mine has cruise so not the same.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Incidentally, some time back there was another thread where I mentioned my BECM was set to Late EDC and I was surprised given it was an early 1995 car. Rick-the-Pick said it depended on what the engine was monitoring. Well, I tried setting it to Early EDC but then it wouldn't start so switched it back. Meant to update the other thread but had lost it.
Makes you wonder when it switched to Late EDC. Started P38 production in 1994? Wonder if you can tell from the chassis number which number yours was off the production line?
Makes you wonder when it switched to Late EDC. Started P38 production in 1994? Wonder if you can tell from the chassis number which number yours was off the production line?
- Posts
- 58,170
- Location
- Preston Lancs.
You and that Nanocom are like a bloody kid playing with a live grenade. One day the pin will fall out.
- Posts
- 1,520
- Location
- Buckinghamshire.
I'm saving this thread so I can be ready with an "I told you so" when the car goes pop!
IIRC Jules, your Nanocom says my cruise is not set, when I do have it fitted.
I've switched it on and off and it didn't seem to make any difference.
IIRC Jules, your Nanocom says my cruise is not set, when I do have it fitted.
I've switched it on and off and it didn't seem to make any difference.
Last edited:
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Have to try to learn. Burnt hand teaches best, as they say. Besides, what could possibly go wrong with the guiding hands of Wammers and Datatek leading me? No, no difference but not worried as I think that it is working normally.
That's odd. Maybe worth raising with BBox then. May already be; not checked for an update for a while.
Think we're done here. No unusual faults. Timing modulation is varying too much and is way too high indicating worn chain / sprockets on lower chain. Only other option is timing electronics itself is getting cranky. Job done.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
My tractor has done double the miles yours has and will still be running when your liners drop onto the tarmac and the pistons bevel our bonnet!
- Posts
- 1,520
- Location
- Buckinghamshire.
My tractor has done double the miles yours has and will still be running when your liners drop onto the tarmac and the pistons bevel our bonnet!
I hope so!
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Incidentally, I've noticed that when you look at the reading in live time the timing modulation variation is only a few percent, much as the manual suggests. It is only when you record a trace over a reasonable time that the higher variation is apparent. I'm not sure these extreme readings are entirely reliable.
- Posts
- 58,170
- Location
- Preston Lancs.
Are you driving around and recording these traces. What part of baselines are read at IDLE with an HOT engine do you not understand?
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
No, done at idle on a warm engine.
I was just making the point that characteristics were different depending on the manner in which you were measuring it. I think that's worth knowing.
I was just making the point that characteristics were different depending on the manner in which you were measuring it. I think that's worth knowing.
- Posts
- 58,170
- Location
- Preston Lancs.
The distance between two points can vary greatly depending how far you stretch your elastic tape measure. Just take the visual readings from the Nanocom. Anything else has you asking silly questions.
Rangeroverbass
Member
- Posts
- 50
- Location
- Southampton
Wammers on. Mine when I go into this I have lots of boxes but there's no value in any except the idle which is 128.is this how it should be?
- Posts
- 58,170
- Location
- Preston Lancs.
The first box top left should be 8 all the rest should be 128.
Rangeroverbass
Member
- Posts
- 50
- Location
- Southampton
Would this be causing any issues do you think? I'll set it to what you say today see what happens
