My First 90

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Today, I drove the 100 miles to my Dads, so he could see the Landy. I found out he used to drive a series back in the late 50's (he doesn't often share such information!!).
I took him out for a little trip which made him smile. He's 87 but got in and out ok. The Landy performed impeccably and kept up 60mph on the A1 no problem :)
That's around 450 miles since I bought her plus 2 off road adventures. I am still grinning :D:D:D
 
My Old Landy said:
Today, I drove the 100 miles to my Dads, so he could see the Landy. I found out he used to drive a series back in the late 50's (he doesn't often share such information!!).
I took him out for a little trip which made him smile. He's 87 but got in and out ok. The Landy performed impeccably and kept up 60mph on the A1 no problem :)
That's around 450 miles since I bought her plus 2 off road adventures. I am still grinning :D:D:D
Click to expand...
Sounds like a very special trip and will make memories for all concerned! Health to enjoy your super D90 and hope there's more such trips :D:D
 
My Old Landy said:
Today, I drove the 100 miles to my Dads, so he could see the Landy. I found out he used to drive a series back in the late 50's (he doesn't often share such information!!).
I took him out for a little trip which made him smile. He's 87 but got in and out ok. The Landy performed impeccably and kept up 60mph on the A1 no problem :)
That's around 450 miles since I bought her plus 2 off road adventures. I am still grinning :D:D:D
Click to expand...
you need to find his land rover from the 50s me thinks
 
The tread on my tyres proved woefully inadequate so I got these s/h off the bay :)
upload_2018-10-16_20-25-41.png

Quite pleased, between 8mm and 10mm of tread and one is new :D
I now have 9 wheels to choose from :rolleyes:
 
neilly said:
Double check your steering lock stop bolts when you fit them to make sure you do not foul the radius arms on full lock.

Cheers
Click to expand...
Cheers I will check. I am hoping that it is ok as they are +8 and that's what mine are supposed to be according to the previous owner :)
But as you already have seen, my truck is full of surprises!
 
My shiny new electric impact driver is fantastic. It came fully charged and I have been using it a lot.
I checked and the battery gauge said it was getting a bit low so, I put the battery on charge.
Flash, Bang, Smoke :eek: not a happy camper!!
Anyway, a quick chat with Amazon and I can return it for a full refund including postage, so not too bad.
(I am just annoyed as I still have tight nuts and bolts to undo!!)
 
My Old Landy said:
My shiny new electric impact driver is fantastic. It came fully charged and I have been using it a lot.
I checked and the battery gauge said it was getting a bit low so, I put the battery on charge.
Flash, Bang, Smoke :eek: not a happy camper!!
Anyway, a quick chat with Amazon and I can return it for a full refund including postage, so not too bad.
(I am just annoyed as I still have tight nuts and bolts to undo!!)
Click to expand...

Not so good, have you identifed the problem yet?

Cheers
 
neilly said:
Not so good, have you identifed the problem yet?

Cheers
Click to expand...

It seems that the slave cylinder has a leak. The wading plug kept the dot4 in the bell housing so didn't show during the trip. When the truck got to our house, I managed to drive it into the garage although the pedal was very low with a sort of on/off action.
Today I got it out of the garage to clean it before I started on it and I could change gear. I pulled the top off the master and checked the oil. After replacing the cap and trying to get it into gear to put it back into the garage, no clutch again......
So I am going to replace the whole hydraulic system, I am thinking of changing the clutch too, do you think I should?
 
My Old Landy said:
It seems that the slave cylinder has a leak. The wading plug kept the dot4 in the bell housing so didn't show during the trip. When the truck got to our house, I managed to drive it into the garage although the pedal was very low with a sort of on/off action.
Today I got it out of the garage to clean it before I started on it and I could change gear. I pulled the top off the master and checked the oil. After replacing the cap and trying to get it into gear to put it back into the garage, no clutch again......
So I am going to replace the whole hydraulic system, I am thinking of changing the clutch too, do you think I should?
Click to expand...

Personally, If it is only the slave then I would only change that, bleeding can be a PITA, but changing a whole clutch when you do not need to seems a waste of time and money. Unless you are bored. :p My slave failed almost 2 years ago, changed it and since then no problems... Except for the wheel bearing..LOL.

Cheers
 
neilly said:
Personally, If it is only the slave then I would only change that, bleeding can be a PITA, but changing a whole clutch when you do not need to seems a waste of time and money. Unless you are bored. :p My slave failed almost 2 years ago, changed it and since then no problems... Except for the wheel bearing..LOL.

Cheers
Click to expand...
I expect the clutch is fine as it seems strong. The master looks ok but the cap breather hole is blocked.
Even if I don't change the master, I think I will buy one 'just in case' :D
I hope you get your bearing fixed! When is the next trip as I am eager to do more than a quarter of the adventure :rolleyes:
 
You must log in or register to reply here.

Similar threads

marksman
Should I offer my collection of def 90 300tdi spares ?
Replies
11
Views
1K
dag019
dag019
S
Freelander TD4
Replies
1
Views
247
Ian M in France
Ian M in France
M
Hello!
Replies
4
Views
708
MelancholyDonkey
M
V
Have been wanting a Land Rover since Born Free in the 70's
Replies
4
Views
732
Freddie17
Freddie17
M
1992 200tdi 90 2.5 Body Parts Catalogue
Replies
5
Views
482
Mepps
M
Back
Top