Locked out

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
B

Bradderz18

Member
Posts
16
Location
Portsmouth, England
So how do you get into a Range Rover Vogue 03 plate with a flat battery?? I can't use the key as the door mech is broken. Any ideas welcome? Is there such a thing as being able to jump it? Without opening the bonnet
 
Something is leading me to suggest a jump via towbar socket, but can't recall if it's via the grey "caravan" charging socket or whether it's possible via normal 7 pin black..... hopefully somneone more sober will amble this way anon...
 
myfirstl322 said:
Something is leading me to suggest a jump via towbar socket, but can't recall if it's via the grey "caravan" charging socket or whether it's possible via normal 7 pin black..... hopefully somneone more sober will amble this way anon...
Click to expand...

If there is a permanent live on the tow socket you can certainly trickle charge it from that but you certainly can't jump it. ;)
 
Bradderz18 said:
So how do you get into a Range Rover Vogue 03 plate with a flat battery?? I can't use the key as the door mech is broken. Any ideas welcome? Is there such a thing as being able to jump it? Without opening the bonnet
Click to expand...
on the p 38, you can wedge top of door open,slide metal coat hanger down ,and hook button up?but don,t know your set up,improvise? good luck
 
Bradderz18 said:
So how do you get into a Range Rover Vogue 03 plate with a flat battery?? I can't use the key as the door mech is broken. Any ideas welcome? Is there such a thing as being able to jump it? Without opening the bonnet
Click to expand...

Are you able to get a jump lead onto the positive of the alternator from beneath? Hoo that to a second battery and the negative to the earth and you might have enough power to unlock? Or as Wammers says you might trickle some charge through the permanent 12V on the supplemental tow socket.
 
Saint.V8 said:
Alternator output is to far up the engine block and sits on the front of the unit near the belts and pulleys....no room for a jump lead - even if you could reach all the way up and get one to it.
Click to expand...

Now there's computer aided design!

Back to the supplementary tow socket and a trickle charger then!
 
Maybe the live on the starter motor as that runs the high power cable direct from the battery on most vehicles??

They do make a charger adaptor for a trickle charger to the caravan socket for people that store vehicles or make one up from motor factor bits?

Steve
 
Ok after a lot of reading ... Drivers side fog light!! Remove the plastic trim, remove the bulb inset some decent copper wire into the positive and negative and connect to a power pack - this provided enough power to open the doors. Boom! Not sure if u could jump it this way but I only needed the door open --- thankyou all for your help
 
Wires not heavy duty enough to jump it but if you can open the doors you can access the bonnet release and either charge battery or get proper jump leads on

Reminds me of the late 80's where they used to smash indicators to fuse the aftermarket alarms
Steve
 
Is it the ground side that's switched on these? I wouldn't personally do this as you could damage the MOSFETS in the BECM.
Much better to find something that is a permanent live from the battery and feed via this.
I used to have a car that regularly killed its battery for no apparent reason and that had a knackered barrel in the door lock but I could still get in the boot.
I fitted an auxiliary power socket in the boot so that when it dies I could power it back up to get it open then jump it at the battery. Much better option is to fix the bleedin lock!!!
 
Did somebody leave the lights on ??

03 L322 Front Fogs are fed through "Module Lighting Switch", so surely to power things via the bulb contacts requires the switch to be on ?

Screen Shot 2017-04-25 at 15.11.10.png
 
pwood999 said:
Did somebody leave the lights on ??

03 L322 Front Fogs are fed through "Module Lighting Switch", so surely to power things via the bulb contacts requires the switch to be on ?

View attachment 122179
Click to expand...
I did wonder that which is why I asked if they were switched via the becm. I assumed that it had backfed into the 12v bus of the becm thus giving sufficient power to open the doors.
If it's simply a switch, it must have been on.
 
The lights were not on. To my knowledge there was nothing on in the car (visible) apart from what drained the battery which I think could of been the AMP in the rear not turning off
 
You must log in or register to reply here.

Similar threads

I
P38 BeCM locked?
Replies
8
Views
685
pwood999
pwood999
awkwardbob
L322 2003 L322 Can’t open bonnet -battery flat
Replies
16
Views
454
marjon
marjon
Maat
P38A Door lock not working
Replies
3
Views
740
Maat
Maat
Radar1946
P38A 12.5 volts and not enough to start engine.
2
Replies
23
Views
1K
Radar1946
Radar1946
feyniriel
P38 alarm and immobilizer problems
2 3
Replies
42
Views
2K
Datatek
Datatek
Back
Top