kds
Well-Known Member
- Posts
- 2,262
- Location
- old,ugly, tired in Lincoln.
Wot he said.
P38A hub nut
- Thread starter ukadamwest
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
- Posts
- 58,170
- Location
- Preston Lancs.
Hub nut is easy. You need 3/4" tackle an axle stand a length of suitable tube and eighteen stones.
sheriff
Active Member
- Posts
- 296
- Location
- Barnsley,Land of the Black Gold
Haven’t got 18 stones will bricks do instead ? 
- Posts
- 58,170
- Location
- Preston Lancs.
Haven’t got 18 stones will bricks do instead ?
As long as they weigh 252 pounds they should be ok, all you have to do then is train them to stand on the tube and bounce slightly up and down.
ukadamwest
Well-Known Member
- Posts
- 2,990
- Location
- Surrey
All back together for the moment. I can't get a 3/4 drive breaker bar locally today. nor a length of tube up to the job. The compressor valve is stuck from when I last did spray paint so can't open the valve up. [sigh]...there's a jaaaaaag specialist down the road I'll pop on to see him after work and slip him a drink for loosening it off on henry_b's suggestion
The good thing though, not one stuck or sheared bolt anywhere, when I did the brakes everything was copper greased so once breaking the torque everything came apart smooth as silk. so once that damn hub nut torque is broken, it will be about 15min to strip down.
Just the hub nut.
The good thing though, not one stuck or sheared bolt anywhere, when I did the brakes everything was copper greased so once breaking the torque everything came apart smooth as silk. so once that damn hub nut torque is broken, it will be about 15min to strip down.
Just the hub nut.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
ukadamwest
Well-Known Member
- Posts
- 2,990
- Location
- Surrey
I learned that years ago when I said to someone holding a club hammer 'when I nod my head you hit it'Trouble is Adam it hurts
ukadamwest
Well-Known Member
- Posts
- 2,990
- Location
- Surrey
There's a new development of houses going up just down the road in what used to be a paddock. after getting everything done back up doing the weekly food shop the mrs suggested we talk a walk down to have a look at them. it's a building site with a show home. along the perimeter fencing are... 2m lengths of scaffold lying in the grass. 'I'm coming back for one of those tonight', says I. no you are bloody not says the boss. Go buy on, not steal one. she has a point. I'll pop up in the next few days to see if I can offer the site foreman a couple of quid for one.. you know.. for next time a hub nut needs doing.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
The problem is you buy a 3/4 bar and then it is a whole new lot of sockets. For the hub nut and maybe a crank bolt? How many times is that coming off? I think the hammer action of the air gun is a bit kinder too. Less likely for things to shear. But then my Indy is 5 minutes away and ccouldn't be nicer.
ukadamwest
Well-Known Member
- Posts
- 2,990
- Location
- Surrey
ukadamwest
Well-Known Member
- Posts
- 2,990
- Location
- Surrey
A 3/4 to 1/2 reducer solves that problem but yes I agree on the impact driver. I'll have to service the compressor as it hasn't been used and I turned the reg down for spray paint which isn't enough to give the pressure for the impact gun. joys of only having a narrow window to do car work as back to the office tomorrow. luckily my new job is 2 miles away rather than the 47 I was doing before. I'll let the wife use the cayenne tomorrow and I'll take the RR and stop in at an indi on the way home all it needs is to be backed off some. it's the OEM hub so probably just needs that impact to break the seal.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Think you'll find the reducer will shear off in an instant.
- Posts
- 16,479
Using a reducer only moves the weak point to the reducer....
ukadamwest
Well-Known Member
- Posts
- 2,990
- Location
- Surrey
Fair point.. compressor now on the list of things to sort
I'd so love to have a plumbed in air system in the garage but the wife will probably freak if I suggest it. my compressor I was given its not your typical home portable one I think the pump is Ingersoll Rand with two air tanks
I'd so love to have a plumbed in air system in the garage but the wife will probably freak if I suggest it. my compressor I was given its not your typical home portable one I think the pump is Ingersoll Rand with two air tanks
Last edited:
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Who's wearing the trousers?!
ukadamwest
Well-Known Member
- Posts
- 2,990
- Location
- Surrey
i do, when i'm allowed to.
ukadamwest
Well-Known Member
- Posts
- 2,990
- Location
- Surrey
http://products.dewalt.co.uk/powertools/productdetails/catno/DCF899P2/
XR 18V BRUSHLESS 3 Sp High Torque Wrench
DCF899P2
Latest generation 18V BRUSHLESS XR Li-Ion High Torque Wrench featuring XR 5.0Ah Li-Ion battery technology
Powerful fan cooled motor delivers up to 950Nm of torque and 2400 impacts per minute for heavy duty fastening applications
Up to 1625Nm of "breakaway" torque ensures removal of the tighest bolts
- Posts
- 16,479
We had one of those at my last place - it was pretty awesome - I not sure it is stuck hub nut awesome, if a 1m breaker bar giving it large won't shift it!
Remember Torque is (very basically) force x length
1N is 0.981 kg....
Average Male is 85kg or so, so that is 833.85N over a 1m length or 834Nm - static, bonuce on it and you are adding in acceleration which will increase the force applied (F=ma etc etc)
Remember Torque is (very basically) force x length
1N is 0.981 kg....
Average Male is 85kg or so, so that is 833.85N over a 1m length or 834Nm - static, bonuce on it and you are adding in acceleration which will increase the force applied (F=ma etc etc)
