How to: lower the manual drivers seat in a RR Classic?

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
UlstermanAbroad

UlstermanAbroad

Active Member
Posts
76
Location
Northern Ireland
Hi Guys
Am having issues with head room in my Dec 94 Range Rover Classic soft dash.
It has a sunroof.
Have taken the front spacers out, from underneath the seat, which helps minimally.
At the rear, the seat is welded to a metal panel underneath.

My mechanic has looked at it and says that the only way to lower the whole seat is to cut out some metal
and reweld it afterwards.

What I'd like to know is. Has anybody solved this problem any other way, which doesn't involve so much work and expense?

Cheers guys,
Miichael
 
UlstermanAbroad said:
Hi Guys
Am having issues with head room in my Dec 94 Range Rover Classic soft dash.
It has a sunroof.
Have taken the front spacers out, from underneath the seat, which helps minimally.
At the rear, the seat is welded to a metal panel underneath.

My mechanic has looked at it and says that the only way to lower the whole seat is to cut out some metal
and reweld it afterwards.

What I'd like to know is. Has anybody solved this problem any other way, which doesn't involve so much work and expense?

Cheers guys,
Miichael
Click to expand...
Open the sunroof, plenty of headroom then:cool:
 
goonarmy said:
How tall are ya?
Click to expand...

+1
I've owned four RRC's (two with sun- roofs) & at 5' 10'' drive with the seat actually raised by one notch. Having said that some people are tall due to long legs, whereas others have long bodies, if you fall into the latter group I guess you will need more than average headroom.
I don't know how to overcome the OP's problem, just that any structural alterations will have to satisfy a MOT tester.
 
Last edited:
Only 6'1" and I've always driven with my back as upright as possible.
I'm definitely not short in reach. It's more about avoiding back pain on long journeys.
Looks like some cuttin and weldin is on the horizon :/
 
UlstermanAbroad said:
Only 6'1" and I've always driven with my back as upright as possible.
I'm definitely not short in reach. It's more about avoiding back pain on long journeys.
Looks like some cuttin and weldin is on the horizon :/
Click to expand...
I have back trouble and was told to recline the seat to a reasonable angle as it reduces the load on the base of the spine. Worked for me
 
I guess we all suffer in different ways :( I've had a lower back problem for the last 18 years & it doesn't get any better with the passage of time. I find the Classic's (velour) seats the most comfortable of any vehicle I've owned & despite the total lack of any steering wheel tilt/reach adjustment can drive long distances (300m in one case) without pain.
I hope the OP finds a solution to his particular problem.
 
Slightly off-piste, but I replaced the two (totally knackered) front seats of my 2 Door Rangie, with a set from a BMW Cabriolet (selected for their built-in seat belts). Took a bit of cutting, grinding and welding but they went in and are way more comfortable than the originals. In short: it's do'able, it'll be more comfortable, do it!
 
Thanks guys.
I bought this vehicle hoping to make a few bob. That was before the market went off a cliff.
Going to keep it stock. Make it as good as my budget allows and hopefully I'll see a return,
post Brexit ;)
 
You must log in or register to reply here.

Similar threads

malcolm_durant
Freelander 1 Storytime: how not to pass your MoT (twice)
Replies
14
Views
3K
ER1C
ER1C
awkwardbob
P38A How much of a pain in the rear is it to replace ventilation ducting
2
Replies
26
Views
2K
RangeRoller dt
RangeRoller dt
UlstermanAbroad
How to: lower the manual drivers seat in a RR Classic?
Replies
1
Views
514
UlstermanAbroad
UlstermanAbroad
stevema
Hi from Malta
Replies
7
Views
931
steve2286w
steve2286w
Clamjamphrie
Introduction to an idiot
Replies
18
Views
2K
Hippo
Hippo
Back
Top