Have I been driving 2wd for too long????

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
It's actually a fairly easy job, especially after you've done it once or twice.
Easier if you have ramps as well, essential equipment for a Freelander owner!
Maybe someone local can give you a hand?

Failing that, it shouldn't be more than an hour's labour.

[Edit] Too slow yet again! [/Edit]
 
bukko said:
It's actually a fairly easy job, especially after you've done it once or twice.
Easier if you have ramps as well, essential equipment for a Freelander owner!
Maybe someone local can give you a hand?

Failing that, it shouldn't be more than an hour's labour.

[Edit] Too slow yet again! [/Edit]
Click to expand...

I have one set of ramps I think I will have to invest in another!!!!:D
 
Aye when I built my garage 30 years ago the pit was always going to be included.
 

Attachments

  • Garage-6.JPG
    Garage-6.JPG
    49.8 KB · Views: 168
  • Garage-2.JPG
    Garage-2.JPG
    81.3 KB · Views: 185
  • Garage-3.JPG
    Garage-3.JPG
    77.9 KB · Views: 180
mikey7985 said:
I have one set of ramps I think I will have to invest in another!!!!:D
Click to expand...

You only need one set and perhaps a couple of blocks. The most important things you will need thou is torx sockets.

Edit: you will also need a big long reach socket to tap the bearing back on. I can't remember off hand what size it is but something like a 32mm long reach socket.
 
Last edited:
Grayo said:
Aye when I built my garage 30 years ago the pit was always going to be included.
Click to expand...

I really need to rebuild mine! I already have a kickbag waiting to hang in there. ;)

Only trouble is my house is surrounded by a river on 3 sides so I'm not sure a pit is such a good idea, unless I build a ramp.
 
I am having a pit whether she likes it or not!!!!!!! :)

I have Torx sockets but no long reach socket that big.....I have an aluminium tube I use for trailer bearings that might do it.

Failing that I will speak to my mate up the road and see if I can use his lift and tools :)
 
bukko said:
I really need to rebuild mine! I already have a kickbag waiting to hang in there. ;)

Only trouble is my house is surrounded by a river on 3 sides so I'm not sure a pit is such a good idea, unless I build a ramp.
Click to expand...

You could line the back of the block work with a pool liner but you would have to put this under the foundation and up each side and back and front as well to completely line the pit. That should stop any water getting in.
 
mikey7985 said:
I am having a pit whether she likes it or not!!!!!!! :)

I have Torx sockets but no long reach socket that big.....I have an aluminium tube I use for trailer bearings that might do it.

Failing that I will speak to my mate up the road and see if I can use his lift and tools :)
Click to expand...

Mike, the big socket has got to be the correct size to avoid any damage to the bearing. The socked goes against the smallest ring and gently tapped on.
 
I will have to make sure I don't balls it up if I do it myself!!!! I would have thought it would have been the biggest ring (outer edge of bearing) to avoid damage to the bearing?
 
I 'think' it was a long 32mm I used too? Either way, the new bearing went on very easy, just be sure to get the cups the right way around- see Hippo's guide, it's quite good. Dunno if right or wrong, but I lubed the rubbers with teflon spray before fitting the cups so they spun easier against the cups until they sorted themselves out.



Quote:
Originally Posted by Spacemonkey...
I used to work there. Nasty place...

...and Basingstoke, and Swindon, and Croydon, and Penge, and Highbury. Lovely places...

Epicuser said:
Hey.....I live in one of those areas......

It is lovely.
Click to expand...

Haha! I moved from Penge to Whitehorse Road and it was an improvement I guess, but... ;)
 
Very common in lots of cars as it's basically the same design. Cleaned my brother's ex-monster's Astra thing's wiper motor contacts and cured it.
 
Well, look on the bright side- you can practice on one, then just swap them over. Minimal time off the road (oh the irony..), then you can clean up the other and sell it on ebay for a profit as reconned! Oh, I'd keep it a while. You know... just in case, like...
 
Spacemonkey... said:
Well, look on the bright side- you can practice on one, then just swap them over. Minimal time off the road (oh the irony..), then you can clean up the other and sell it on ebay for a profit as reconned! Oh, I'd keep it a while. You know... just in case, like...
Click to expand...

Lol.......This is going to be the story of my life with LR products isn't it???????????:rolleyes::rolleyes::rolleyes:
 
Well..... I still have a few bits in the shed from my old Series 3, my old L series FL and various Pajeros and Delicas. With 4x4s, you just never know..

Funny though, we think of 4x4s as strong and reliable, but in my experience they break more often and at lower mileages than 'normal' cars, and that's even without abuse off road. Hmm... I think we've been conned!
 
You must log in or register to reply here.

Similar threads

Kerlaan
Freelander 1 Propshaft carrier bearings - how long to change them? [SOLVED]
Replies
6
Views
1K
Kerlaan
Kerlaan
Atomician
Fl1 with selectable 4wd?
Replies
2
Views
414
GrumpyGel
GrumpyGel
B
vibration under load.
Replies
1
Views
645
andyfreelandy
andyfreelandy
xDParis64
IRD Fail???
2
Replies
25
Views
3K
Alibro
Alibro
N
Rear diff issues
Replies
11
Views
1K
Jimmy1981
J
Back
Top