Harmonic Balancer - where to get 4 bolt puller

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Tirran

Tirran

Well-Known Member
Posts
251
Location
South Lanarkshire
As expected my Harmonic Balancer is proving a complete b’stard to remove, does anyone know where I can get a 4 bolt puller? Everything I have seen so far is only 3 bolt.

I don’t want to damage it as a replacement is around £180!!

cheers

Bill
 
I drilled a piece of 1/2" plate for four securing bolts and drilled tapped centre hole for withdrawl bolt .
 

Attachments

  • IMG_1411.JPG
    IMG_1411.JPG
    281 KB · Views: 189
  • IMG_1412.JPG
    IMG_1412.JPG
    194.4 KB · Views: 210
Iirc the cheap tdi timing kits have a large round plate for holding the inj pump pulley in place whilst removing the pump, these also fit the crank damper.
Also good for pullng the cambelt gear off of the crank as well, but do need some extra bolts for that job.
 
Tirran said:
It is, never thought about it as it is only the flywheel stop and FIP shaft I’ve used.
I hope it has the strength to pull off the Damper. Thanks.
Click to expand...

I spent an age levering/hammering a 200 damper, then thought oh yeh that may work, the bloody thing just slid off with no issues!
 
lynall said:
I spent an age levering/hammering a 200 damper, then thought oh yeh that may work, the bloody thing just slid off with no issues!
Click to expand...
Exactly what has happened tonight, used the timing kit items and off she came no problem, right tools and the jobs much easier.
The problem now is that the cam toothed wheel has a timing dot, the FIP wheel has two red dots of paint with no timing dot. My thinking is that the cam timing dot aligned with the arrow on the timing case , plus the engine at no1 tdc the locking pin should go into the FIP wheel. I know the crank rotates twice to move the cam and FIP into position. Then I can remove and replace the timing belt.

is my thinking sound?
 
Fip use one of the timing pins, you can see the hole through the pulley itself, and the hole is at the top.
The dots will just be a mech in the past doing it his way, or doubling up to make sure.
Basically crank slot at 12 oclock, insert timing pin into the flywheel housing and engage it into the flywheel slot, line up cam marks, pin in fip pulley, (pulley bolts loosened) fit belt, tension belt, tighetn fip pulley bolts, remove pinsm rotate engine by hand a couple of times, and make sure all the pins still fit, job done.
 
lynall said:
Fip use one of the timing pins, you can see the hole through the pulley itself, and the hole is at the top.
The dots will just be a mech in the past doing it his way, or doubling up to make sure.
Basically crank slot at 12 oclock, insert timing pin into the flywheel housing and engage it into the flywheel slot, line up cam marks, pin in fip pulley, (pulley bolts loosened) fit belt, tension belt, tighetn fip pulley bolts, remove pinsm rotate engine by hand a couple of times, and make sure all the pins still fit, job done.
Click to expand...
Thanks, just as I was intending, great thing about this forum is the ability to check your thinking.
 
93D1D06F-6899-45FE-AA50-59CB6FA53660.png


Picture worth a 100 words
Did mine with a locking pin in flywheel , FIP tool sliding fit in hole
Crank slot lined up with arrow
Cam wheel dimple lined up with casting

NB if you invert your engine it will look like pic above
 
Last edited:
Thanks that was at the end of a rebuild , it was really clean inside , it’s in my Series 3 now and running clean too no probs on any of the cogs getting them off
BD2686EA-A80C-40E8-82CD-1EB56B3BCE10.png
 
You must log in or register to reply here.

Similar threads

xDParis64
Freelander 1 Skid Plate Bolt Sizes + Engine Compression
Replies
19
Views
758
J_D
J_D
D90 Td5
Aftermarket Hubs
Replies
2
Views
124
tottot
tottot
L
GETTING SWIVEL TO AXLE BOLTS OUT!! - they are out!!!
2
Replies
29
Views
2K
Forrest Gump
F
A
Series 3 How to remove overdrive lever
Replies
2
Views
624
Ausman123
A
F
Where to sell FL1 if I don’t have sufficient posts?
Replies
13
Views
884
Dar ran Dar ran
Dar ran Dar ran
Back
Top