P38A Halft shaft clip

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Quick update I can see the shaft going in from the other side I’ve just ordered a cheap second hand one that I’m going to just try and put in without the cv joint on it I’ve that goes in then I no the bit inside is all ok just to save me taking my cv joint off
 
Yer but I’ve I do that and screw the cir clip again I will have to wait again for replacement I’ve done the short side and that seems ok
 
Got one side done and new clips will be here today for me to probably take off the other side again and try an get the poxy haft shaft in the axle all the way but least got short side done
 

Attachments

  • 75EF8D1F-8226-47A4-956C-335511B116E0.jpeg
    75EF8D1F-8226-47A4-956C-335511B116E0.jpeg
    394.4 KB · Views: 68
Mega problems on other side bit the bullet took the hub an cv joint off again and still the shaft won’t go in it’s starting to go in the diff a bit because I’ve I turn the other side it turns the shaft on the offside any suggestions much appreciated before I bye a new shaft
 
I’ve taken couple off photos in one you can see 4 or 5 small marks where I banged it in a little bit but it’s clear around the rest of the splines any suggestions much needed
 

Attachments

  • image.jpg
    image.jpg
    607.2 KB · Views: 87
  • image.jpg
    image.jpg
    596.2 KB · Views: 86
If you have a file that's fine enough you could dress the damage and try again. If it came out, it should go back in?
Did you have any diff noises beforehand?
 
No mark no noises I heard from diff ive tried file a bit still not working I’m waiting for an old second hand one to arrive in the week then when I get home next Friday will try it I’ve it goes in all good I’ve not I suppose I will have to strip the diff casing off and have a look
 
pete12345 said:
No mark no noises I heard from diff ive tried file a bit still not working I’m waiting for an old second hand one to arrive in the week then when I get home next Friday will try it I’ve it goes in all good I’ve not I suppose I will have to strip the diff casing off and have a look
Click to expand...
From the damage it looks like you haven't had the splines parallel with the ones in the diff.when you slide the halfshaft in you have to support the shaft on your hand and gently press down on the c/v so the inner end tilts up.when it enters it will slide in.but a Dremmel and clean off the burrs.
 
tomcat59alan said:
From the damage it looks like you haven't had the splines parallel with the ones in the diff.when you slide the halfshaft in you have to support the shaft on your hand and gently press down on the c/v so the inner end tilts up.when it enters it will slide in.but a Dremmel and clean off the burrs.
Click to expand...
Bloody burrs again... Furry gits.. :rolleyes:
 
Cleaned it up on the end again will wait for second hand one to arrive an try that but drained oil from diff not good colour and plug bit caked up but when cleaned of onto piece of white paper there were no big bits at all I’ve the secondhand haftshaft doesn’t go straight in it’s new diff I suppose
 

Attachments

  • 0D7712D2-7A28-4DF8-8292-5B8222879253.jpeg
    0D7712D2-7A28-4DF8-8292-5B8222879253.jpeg
    498.2 KB · Views: 72
  • 41C574FA-755C-4604-B746-9056861702B4.jpeg
    41C574FA-755C-4604-B746-9056861702B4.jpeg
    356.7 KB · Views: 68
You must log in or register to reply here.

Similar threads

T
Newbie , Drive shaft installation help please
Replies
3
Views
663
J_D
J_D
A
FACELIFT Freelander 2005 outer front CV joint - specialized ?
2
Replies
25
Views
2K
Arnodafe72
A
Skihorn
Door Sill Trim Clips
Replies
8
Views
869
Skihorn
Skihorn
C
Front Drive Shaft CV/Gator boot
Replies
4
Views
1K
htr
htr
D
Half shaft install help!
Replies
11
Views
2K
Bearhound
B
Back
Top