fuse 2 failure ???

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
J

jimsnapon

New Member
Posts
72
Location
kilmarnock
hi, good evening hope some one can help me , i have a 2001 on a y plate 4.0 with the error message on dash saying fuse 2 failure . ive checked and replaced fuse to no avail, so i decided after reading all the posts on here on similar problems, to remove drivers seat and remove top off the becm.this i did and to my horror i could see various states of corrosion on the in and around diff relays and joints, so i sprayed contact cleaner on the board and set about cleaning the said corrosion with a hard toothbrush then i got a hairdryer and dried off the board and sprayed again just to do a final clean ,
i have now plugged all the connectors back into board and started up car but it has made no diff at all, still got fuse 2 failure message and all the other false errors that i had before, anyone got any ideas before i build the car back up ? any help asap would be brill. as car is now blocking drive in this taken apart state and will need to build it back up to move it to let other members of family out with there cars lol

regards jim
 
thanks datatek for your quick answer,
ive had a look but dont possess any type of magnifying glass ,
however ive took a picture of the offending part of the board not the best one i admit
but im thinking there might be a problem under the big relay you can see in top left of pic that yellow wire is the one leading to fuse 2 , on fuse box
 

Attachments

  • becm on yeba.jpg
    becm on yeba.jpg
    240.8 KB · Views: 925
cheers for that bit of info Sean , :D
any ideas can the top of board be changed with one from another car without any interruption to keycode and things like that ?

cheers jim
 
jimsnapon said:
thanks datatek for your quick answer,
ive had a look but dont possess any type of magnifying glass ,
however ive took a picture of the offending part of the board not the best one i admit
but im thinking there might be a problem under the big relay you can see in top left of pic that yellow wire is the one leading to fuse 2 , on fuse box
Click to expand...

If it were me I would want to remove that relay from the board and check any tracks underneath it, but I have the kit to do that. I would also want to test the relay. PM Irishrover and see what he thinks.
 
Datatek said:
If it were me I would want to remove that relay from the board and check any tracks underneath it, but I have the kit to do that. I would also want to test the relay. PM Irishrover and see what he thinks.
Click to expand...


Good call datatek :) Jim is the rest of the board as bad as this part near the relay? i would not like to try repairing that board, id replace with a fresh one. :) was the relay cracked ontop before you opened the lid?
 
Last edited:
hi datatek, further to my earlier ? regarding swapping top board from another becm do you think this is possible with no worries regarding keycode lockout etc etc

regards jim
 
hi, just thought id let you's all know i have stripped out old corroded board out of becm and replaced with the top board out of another becm reconnected and hey presto started up and faults all gone , ie windows working , heater fans now working, and fuse 2 failure error message gone from dash,

love it when a plan works lol
 
You must log in or register to reply here.

Similar threads

rustyrangie
Classic fuel pump fuse location??
Replies
5
Views
197
Mark Piercy
Mark Piercy
P38 guy
Relay 6 and relay 7 relocating.
Replies
19
Views
1K
Datatek
Datatek
G
P38A Glow plug relay fuse
Replies
4
Views
777
Grrrrrr
Grrrrrr
I
Air.Susp.Inactive message on 2005 L322
Replies
4
Views
589
invisible999
I
ar1g3
P38A Bulb Failure message preconditions?
Replies
6
Views
598
Datatek
Datatek
Back
Top