Freelander 1 Frustrating morning belting the propshaft.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Burnham said:
Aye, I'm doing some renovation work on a cottage at the mo, so I'll bring one of the stone chisels home tomorrow. (I leave all the building tools on site, to much faff carrying it back and forth.



Errr, I think I'll pass on that option for the mo ta!!
Click to expand...

I wouldn't worry about doing this. I replaced the VCU carrier bearings on mine and noticed one of the bolts was missing, never replaced it and done over 30k since then. It was mentioned on the MOT last week that the rear UJ was showing signs of wear, I guess this is due to the missing bolt allowing some movement at that point?
 
S1monm said:
I wouldn't worry about doing this. I replaced the VCU carrier bearings on mine and noticed one of the bolts was missing, never replaced it and done over 30k since then. It was mentioned on the MOT last week that the rear UJ was showing signs of wear, I guess this is due to the missing bolt allowing some movement at that point?
Click to expand...
Running with the bolt missing is dangerous. Both the ird and rear diff move. The vcu doesn't. The front prop has some give from the sliding joint.
 
Hippo said:
Running with the bolt missing is dangerous. Both the ird and rear diff move. The vcu doesn't. The front prop has some give from the sliding joint.
Click to expand...

Can't see there being enough movement in the rear diff to allow the prop to come out though Hippo
 
S1monm said:
Can't see there being enough movement in the rear diff to allow the prop to come out though Hippo
Click to expand...
The correct mounts contain stiff rubber. As it ages and weakens yer get more movement. Add to this the forces involved when oft road or wheel spinning on gravel when traction control and the vcu are working hard... It's not worth the risk. You would think it just sits there but I filmed mine while oft road. Theres some movement but not a massive amount. The props don't slide that far onto the vcu. Unfortunately peeps on the web read stuff on ere and follow it. It's not a good idea to run without the bolt. They're cheap to buy.
 
Hippo said:
The correct mounts contain stiff rubber. As it ages and weakens yer get more movement. Add to this the forces involved when oft road or wheel spinning on gravel when traction control and the vcu are working hard... It's not worth the risk. You would think it just sits there but I filmed mine while oft road. Theres some movement but not a massive amount. The props don't slide that far onto the vcu. Unfortunately peeps on the web read stuff on ere and follow it. It's not a good idea to run without the bolt. They're cheap to buy.
Click to expand...

Point taken mate. I'll get a new bolt fitted when I do the bearings again in a couple of weeks. Don't suppose you know what the part number is for the U shaped spacer do you?
 
if you can when belting it with a hammer keep it on the floor as if you do it on the bench that will have a little play in it and you will not get the full force of the hammer blow
 
I am sure you'll all be thrilled to learn that belting it with a suitably large chisel separated the prop shaft from the VCU. I did leave it to soak with a spray or five of WD40 (all I had to hand) for a week or so, and when I came to hit it I took just three knocks to free off the front shaft, the rear shaft actually just fell off!

Considering the belting I'd given them both to no avail a couple of weeks ago, I think it was the "lubricant" that helped.

Cheers all! Loads of interesting info!
 
You must log in or register to reply here.

Similar threads

M
propshaft
Replies
10
Views
2K
MGT
M
Saint.V8
  • Sticky
200TDi Timing Belt Change and Cylinder head Refurb How To....
Replies
5
Views
14K
IamRobbie
IamRobbie
Saint.V8
200TDi Timing belt change and cylinder head refresh HOW TO...
Replies
6
Views
9K
toms3
T
R
FBH all you need to no info
Replies
7
Views
3K
rhodie
R
Dr_evil
Series King Cab
61 62 63
Replies
1K
Views
125K
discomark10
discomark10
Back
Top