Freelander TD4 2005
- Thread starter JC600
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Pompey
Well-Known Member
- Posts
- 729
Found the part I required ordered it, then got a refusal notice, Part not available, not important I am the choke at the moment 
cant remember, apart from the boat, the last vehicle I had with a manual choke
cant remember, apart from the boat, the last vehicle I had with a manual choke
JC600
Well-Known Member
- Posts
- 1,103
Found the part I required ordered it, then got a refusal notice, Part not available, not important I am the choke at the moment
Rubbish service that, my mk3 Escort had manual choke and my old mk3 fiesta. I prefer carb engines, took me the best part of a year to get the efi engine running right. It's a nippy little car now though, only 110 bhp but car weighs less than 800kg.
22mm wheel nut covers, greased inside to cover my rusty nuts nuts lol
Do they fit in the wheel nut hole ok?
JC600
Well-Known Member
- Posts
- 1,103
Yeah, spot on. Tried one to start with, to make sure I could remove them.
Your BBS rims have shallower holes than my Trek rims. I expect they would be more difficult to remove from mine. They look perfect on yours though.
JC600
Well-Known Member
- Posts
- 1,103
Your BBS rims have shallower holes than my Trek rims. I expect they would be more difficult to remove from mine. They look perfect on yours though.
Cheers, I had them on my old Freelander. On the 16" alloys. They come with 2 sizes of removal tools too.
4Bee4Bee
Well-Known Member
- Posts
- 322
- Location
- Shropshire
Steering wheel came up nicely!. What did you use to restore life back in to it? Mine currently looks like your original picture
JC600
Well-Known Member
- Posts
- 1,103
Steering wheel came up nicely!. What did you use to restore life back in to it? Mine currently looks like your original picture
Thanks, this is the kit I brought http://www.ebay.co.uk/itm/251378275765?_trksid=p2057872.m2749.l2649&ssPageName=STRK:MEBIDX:IT
Just take your time when doing it, and good prep, makes for a good finish.
4Bee4Bee
Well-Known Member
- Posts
- 322
- Location
- Shropshire
Thanks, will give it a go. I've seen things like this, but always been a bit sceptical. But the finish looks a great improvement.
JC600
Well-Known Member
- Posts
- 1,103
Thanks, will give it a go. I've seen things like this, but always been a bit sceptical. But the finish looks a great improvement.
This is the finish on a 30 year old steering wheel.
Before
During
After
What's wrong with the Vortex rims then?New wheels ordered.
JC600
Well-Known Member
- Posts
- 1,103
2 keeping leaking on the rims, been cleaned up twice now and resealed but still leaking. Have to pump them up every week. Was going to get them refurbished, but a lot of money if they still leak afterwards.
Alibro
Well-Known Member
- Posts
- 7,182
- Location
- Northern Ireland
Have you tried this?2 keeping leaking on the rims, been cleaned up twice now and resealed but still leaking. Have to pump them up every week. Was going to get them refurbished, but a lot of money if they still leak afterwards.
http://www.ebay.co.uk/itm/Goop-Punc...697799?hash=item5d722fdc87:g:MkkAAOSwiQ9ZQoG~
I've used it a few times and normally works well.
Last edited:
JC600
Well-Known Member
- Posts
- 1,103
They've used proper tyre sealant, still leaks. I don't mind, new rims should look good. Weren't too expensive either, after shopping around. 6mm more clearance too.
I had 1 of my Trek rims leak after my Maxxis 771 were fitted. I had to pump it up weekly for about 6 months. Strangely the leak stopped after I swapped the wheels from side to side. I assume the tyre has bedded in and so stopped leaking.2 keeping leaking on the rims, been cleaned up twice now and resealed but still leaking. Have to pump them up every week. Was going to get them refurbished, but a lot of money if they still leak afterwards.
Similar threads
