FIP Strip with lots of pictures

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
JohnnyCrash

JohnnyCrash

New Member
Posts
1,917
firstly I must say sorry for the colour of the internals of this pump, this has been run on Bio, SVO and Black diesel and is covered in gumming, no doubt the reason this pump died, however it did manage 150k miles so it's not all doom and gloom



First you need to tackle the Bosch security bolts (if you can't crack this don't both going any further) the top bolt hammer on a 7mm socket and the smaller bolt can be tapped round with a small flat punch (or screwdriver) and a hammer, then removed with needle nose pliers without damaging the head.



Then remove the other Torx bolts
 
Remove the middle section, making working on it much easier



Now undo all the red screw, and the Blue ones (they are left hand thread)


you will also need to unpick the electrical connectors (purple) I used heat and a flat head screwdriver

bend back the 2 wires highlighted in green
 
Last edited:
with the top removed you have access to the coil, using a deep 7mm socket to remove the studs will release everything



remove the springs line up the shaft and you will be able to remove the coil


 
Anybody can strip a pump down it's putting it back together and setting it up so that it works where the trick comes in. Have you seen an injection pump test and set up rig? :D:D
 
wammers said:
Anybody can strip a pump down it's putting it back together and setting it up so that it works where the trick comes in. Have you seen an injection pump test and set up rig? :D:D
Click to expand...

Lol I'll give you some praise jonny. Well done you mate very good write up :)
 
wammers said:
His next project is a stripping a Trent 1000 followed by the Hardron collider. :D:D
Click to expand...
Trent Family....simples...:D:D:D:D

Hadron Collider is just a giant magnet! just take yer Prince Albert out before you get too close! :eek::eek::eek:
 

Attachments

  • Trent_Family.jpg
    Trent_Family.jpg
    234.6 KB · Views: 195
Saint.V8 said:
Trent Family....simples...:D:D:D:D

Hadron Collider is just a giant magnet! just take yer Prince Albert out before you get too close! :eek::eek::eek:
Click to expand...

Yep but a bloody complicated giant magnet. Point is stripping something is really easy, it's putting it back together and getting it to work, that is the bitch. :D:D:D
 
not worried really, stripping without breaking something is the hardest part.

the rebuild should be simple enough once everything is cleaned up
 
Personally, I couldn't be bothered, too time consuming and set up may prove impossible.
I'll send mine off to Diesel Bob or Bosch for overhaul when the time comes as I have a spare.
 
I'm sure Johnny marked everything up on all sides before starting.

Resoldering those little copper strips / wires (I think you coloured them purple?) can be tricky.
 
You must log in or register to reply here.

Similar threads

dwarfer
L322 in two years of ownership...bought with 121k now 123k
2
Replies
29
Views
3K
Agarange
A
BulletBrindle
How I fixed my TD5 ECU (maybe worth doing for preventative reasons too)
2
Replies
33
Views
10K
BulletBrindle
BulletBrindle
Henry_b
P38A ZF4HP24/22 Fluid Change Procedure.. "How To"
2
Replies
23
Views
5K
Henry_b
Henry_b
Pluribus
Freelander 1 Inlet manifold replacement - Updated with steps and pics :)
Replies
8
Views
2K
Alibro
Alibro
Stanleysteamer
making your ignition key work in a Disco 2
Replies
18
Views
3K
Stanleysteamer
Stanleysteamer
Back
Top