- Posts
- 2,427
- Location
- Isle Sheppy
brought myself an engine stethoscope will find out where this noise is coming from can I post sounds on here I've I record it somehow for bit of advice tomorrow
P38A Finding that strange sound
- Thread starter pete12345
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
brianp38dse
Well-Known Member
- Posts
- 20,067
- Location
- heathrow
You can up load videos on here I believe you up load them to you tube first then copy them over.
- Posts
- 2,427
- Location
- Isle Sheppy
I have managed to record this sound it's a m4a file I don't have a utube account is that The only way to get it on here cheers for advice
- Posts
- 2,427
- Location
- Isle Sheppy
- Posts
- 2,427
- Location
- Isle Sheppy
Mabey exhaust manifold area
brianp38dse
Well-Known Member
- Posts
- 20,067
- Location
- heathrow
Sounds like exhaust gasket or loose spark plug to me.
Orangebean
Active Member
- Posts
- 137
- Location
- South Hams, Devon
I'll go for the favourite, just 'cos nobody else has
Head Gasket
Compression test the pots nearest the noise, or a quick leak-down will confirm
Head Gasket
Compression test the pots nearest the noise, or a quick leak-down will confirm
- Posts
- 2,427
- Location
- Isle Sheppy
No water loss or water in the oil so hopefully not head gasket when u say lean down do u meen just listen near the head I've done that but sounds lower thinkin exhaust gasket also how hard are they to replace thanks for the suggestions
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Depends where it goes and how bad it is. I think @MrGorsky 's made a ticking noise like an exhaust gasket leaking when his went but he caught it very early. There was no other indication on his but he put UV dye in the water and sure enough, a day or so later the dipstick was glowing under a UV light with droplets.
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
This is the sound of a broken HG between the cylinder and outside world..
quite a distinctive sound..
quite a distinctive sound..
Orangebean
Active Member
- Posts
- 137
- Location
- South Hams, Devon
Head gaskets don't have to go into a waterway or oilway. They can just blow straight between pots or direct to the outside world either into valley or below exhaust. They then just chuff, in a very similar way to yours.
Here's one I blew earlier- nowhere near a waterway or oilway, just chuffed
- Posts
- 2,427
- Location
- Isle Sheppy
Cheers orangebean I have got a combustion test kit and will check that out in the morning an post results u wouldn't happen to know what plug does which cylinder coz it says I can test each cylinder aswell thanks for the info
- Posts
- 2,427
- Location
- Isle Sheppy
I've done a combustion test with the blue liquid and its bluer than blue and no crud on oil filler cap haven't done a dye test but fink I be going down the manifold gaskets route or manifolds I've it's cracked do u fink I should still do the dye test just to be sure
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
As said above head gaskets don't have to go into a waterway or oilway. They can just blow straight between pots or direct to the outside world either into valley or below exhaust
If the gasket has broken between a cylinder and outside.
A dye test won't show up fook.
If the gasket has broken between a cylinder and outside.
A dye test won't show up fook.
- Posts
- 2,427
- Location
- Isle Sheppy
So my next question is how difficult is it to remove the manifold myself and replace do I need to book a week off work
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
The exhaust manifolds are relatively easy.
The lower manifold bolt by cylinder 8 can be a pain.
However It's the damn heat shields that are a pain in the arse!!
Replacing the manifold gaskets is a 15-20min job which turns into 2-3 hours because of the damn heat shields!!
The lower manifold bolt by cylinder 8 can be a pain.
However It's the damn heat shields that are a pain in the arse!!
Replacing the manifold gaskets is a 15-20min job which turns into 2-3 hours because of the damn heat shields!!
- Posts
- 2,427
- Location
- Isle Sheppy
Cheers mate do they crack that often or is it probley just the gasket also is it worth doing both sides
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
I personally haven't heard many stories of them cracking but manifold gaskets do fail !
Doing both sides is a good idea the lower manifold bolt from cylinder 8 can be a pain because getting a ratchet in is quite difficult thanks to the lack of clearance is caused by steering column components.
Doing both sides is a good idea the lower manifold bolt from cylinder 8 can be a pain because getting a ratchet in is quite difficult thanks to the lack of clearance is caused by steering column components.
- Posts
- 2,427
- Location
- Isle Sheppy
Glad they don't fail that often because can't find part numbers for them
Orangebean
Active Member
- Posts
- 137
- Location
- South Hams, Devon
ERR6733 for the manifold gasket (2 per head)
ESR3260 for the downpipe gasket (1 per side)
Take the extra 10 mins to pop the wing liner off. Makes access to the shield bolts, as well as manifold bolts, easier.
ESR3260 for the downpipe gasket (1 per side)
Take the extra 10 mins to pop the wing liner off. Makes access to the shield bolts, as well as manifold bolts, easier.
