Disco 2 Failed injector? TD5

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Good news, your pic has turned up.....:p...lots of oil.

Keep the EGR, just in case one day some jobsworth demands they are fitted for an MOT, Highly unlikely but you never know.

Cheers
 
TAH said:
My EGR has a gas cooler on it, and I didn't order enough blanks, so I've left that on there and blanked the EGR side for now - plus had to repair the top coolant leak off pipe from that as it was so brittle it broke as I moved it. Pain.

(Begs the question, if you do remove it totally what do you do with the associated coolant pipes?
Or do you just leave it in place blanked off?).
Click to expand...

Good to hear.
Regarding the EGR removal,yes, there are generally two types on the Disco 2 Td5 engine; with and without the heat exchanger.
If you decide to remove the whole lot, EGR valve, pipework and heat exchanger from the front of the engine, then instead of just blanking off the water pipes, the should be connected to allow a flow through them. There are other devices on that part of the cooling circuit.
I've attached a .pdf which I was given when I removed mine a few years back.
 

Attachments

  • TD5 EGR Removal.pdf
    280.6 KB · Views: 244
  • Like
Reactions: TAH
neilly said:
Good news, your pic has turned up.....:p...lots of oil.

Keep the EGR, just in case one day some jobsworth demands they are fitted for an MOT, Highly unlikely but you never know.

Cheers
Click to expand...
just added links to the post a couple back as well - of the ECU side
 
Something to keep in mind, when you are going to do your next oil change.

Oil pump bolt. Yours is a 2002 , so as far as I am aware it should be OK, but I have heard rumours that some later ones failed. It is on my to do list for my next oil change. Have a look at the discovery2 website.

Not wanting to scare you or be a worrymonger, but it is something you should make an educated decision on.

Cheers
 
brian47 said:
Good to hear.
Regarding the EGR removal,yes, there are generally two types on the Disco 2 Td5 engine; with and without the heat exchanger.
If you decide to remove the whole lot, EGR valve, pipework and heat exchanger from the front of the engine, then instead of just blanking off the water pipes, the should be connected to allow a flow through them. There are other devices on that part of the cooling circuit.
I've attached a .pdf which I was given when I removed mine a few years back.
Click to expand...

Thanks - Thats what I've done (Blank fitted to position 'B') on the EGR end of the heat exchanger. The rest of it is still there and I've left the coolant pipes connected. I was thinking of removing it when I assumed it was only the top small pipe back to the header tank, but having seen the larger coolant pipe coming out of the bottom I didn't want to get involved :)
 
neilly said:
Something to keep in mind, when you are going to do your next oil change.

Oil pump bolt. Yours is a 2002 , so as far as I am aware it should be OK, but I have heard rumours that some later ones failed. It is on my to do list for my next oil change. Have a look at the discovery2 website.

Not wanting to scare you or be a worrymonger, but it is something you should make an educated decision on.

Cheers
Click to expand...
just had a read - and now want to unread it :) -
I'll bear that in mind when I do the next service. Limited area at mine to get it up off the ground (under bonnet stuff is ok but I don't have a drive outside the house as such, just a farm track -
Hopefully the fact its been in there 14years means it'll stay in for another few months until I get in there.

In terms of doing it - just a case of ordering the bolt and sump gasket from one of the many suppliers ?
 
TAH said:
just had a read - and now want to unread it :) -
I'll bear that in mind when I do the next service. Limited area at mine to get it up off the ground (under bonnet stuff is ok but I don't have a drive outside the house as such, just a farm track -
Hopefully the fact its been in there 14years means it'll stay in for another few months until I get in there.

In terms of doing it - just a case of ordering the bolt and sump gasket from one of the many suppliers ?
Click to expand...

Yes, also check the gearbox / sump cross member bolts, they seize up, if for any reason a garage has gone in there, you may find they have had to break off the bolts and may have welded it back in place, ( half mine are welded the other half bolted:p) I keep thinking about doing mine, but then I put it off. AFAIK the risk is really , really low on the later vehicles. But for the sake of a £5 bolt and gasket when doing an oil change I then think I am stupid not doing it........:oops: Choices , choices..........

But , I thought it was best to warn you, at least you are aware of it now. Sorry....LOL.

Cheers
 
  • Like
Reactions: TAH
I dumped the cooler on my 90 never had an issue, also recently got rid of it on my 110 again no issues. You can blank it off right round to the oil cooler on the right of the engine if you want all that extra pipe work out the way. I've yet to do this but I will soon when I do a coolant change.

Theres so much crap in a TD5 engine bay its unreal! Removing it all just makes doing other jobs a little easier.

As mentioned keep it all tucked away somewhere just incase, its unlikely but who knows as everyone hates diesels now...

Only thing that is a pita is getting the allen bolts off the manifold, on my 90 I had to remove the bloody exhaust manifold which in turn snapped studs in the head! I would Plus Gas the bolts daily
 
You must log in or register to reply here.

Similar threads

S
Disco4 rough idle after injector issues
Replies
8
Views
348
Stevie135
S
Cyrus 200
Injector issue
Replies
5
Views
398
Andy Warren
Andy Warren
G
Disco 2 TD5 white smoke at idle
Replies
18
Views
669
GaryWrench
G
T
Frelander 1 bad starting and no power
Replies
2
Views
736
Freddie17
Freddie17
A
Freelander 1 TD4 non start... No pulse to injectors!
Replies
2
Views
752
brianp38dse
brianp38dse
Back
Top