discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
O
M
G
:Eek:
M
G
:Eek:
Essex lanes
- Thread starter goonarmy
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
wangie46
Active Member
- Posts
- 963
- Location
- Lakeside Essex
Gents had some bad news today, the old boy that I bought a 90 for at the beginning of the year had it stollen last night off his drive, looks like its that time of year again, scumbags, so just a heads up to keep ya fenders locked up well and be on your guard.
Co-Pang-Yang
Well-Known Member
- Posts
- 2,930
- Location
- Colchester, Essex
Hopefully me and Mike will be doing a bit of laning Sunday afternoon to test my 'Fender. All are welcome to join us.
Brian S
Well-Known Member
- Posts
- 2,886
- Location
- Braintree, Essex
We will be there. Any idea where you are going?
How about Violets? Might be a bit damper now.
How about Violets? Might be a bit damper now.
mikeyt
Active Member
- Posts
- 299
We will be there. Any idea where you are going?
How about Violets? Might be a bit damper now.
Sounds like a good idea!! i was thinking the same, and then would be rude not to visit standon ford!
On that pic its just tacked on to the return edges of the crossmember, there is a plate that then fits into the member to tie it all together, you can see it on this pic (and my dodgy painting as well):
Its got 4 plates like this, its not going anywhere this member, just need to rewire the back end, fit the starter and alternator, clutch slave and master, stick up the roof lining, get the washers sorted, fit the boost and oil gauge and mount the rear recovery points... not to much to do then!
Nice one just thought i would mention incase it had not been welded.......
antk
Member
- Posts
- 52
- Location
- harlow, essex
Will be up for some lanes Sunday 2
- Posts
- 1,692
- Location
- towie hell
How did you manage to cut the small plates upOn that pic its just tacked on to the return edges of the crossmember, there is a plate that then fits into the member to tie it all together, you can see it on this pic (and my dodgy painting as well):
Its got 4 plates like this, its not going anywhere this member, just need to rewire the back end, fit the starter and alternator, clutch slave and master, stick up the roof lining, get the washers sorted, fit the boost and oil gauge and mount the rear recovery points... not to much to do then!
Jongould
New Member
- Posts
- 3,185
- Location
- Colchester
How did you manage to cut the small plates up
I made 2 more to completely box it in in the end, I added a small drain hole towards the bottom of the replacement chassis sections to allow the water out as its bound to get in somewhere...
- Posts
- 1,692
- Location
- towie hell
There should have been 4 small plates to completely box it in
Jongould
New Member
- Posts
- 3,185
- Location
- Colchester
Ah, I only had 2, I did think that. It don't matter, I used the off cut off from the chassis plates so it's same gauge e.t.c.
This thing will never be moving, the quality is top notch! Well happy with, looking forward to putting it to the test...
- Posts
- 1,692
- Location
- towie hell
Im glad your happy, I bet those other plates are in the back of your van!
Jongould
New Member
- Posts
- 3,185
- Location
- Colchester
Quite possibly, it's a bit of a mess in there, was easy enough to make the plates up...
Co-Pang-Yang
Well-Known Member
- Posts
- 2,930
- Location
- Colchester, Essex
probably best I try and get over to Anglia hose in the morning then. 7 connectors for the breather kit isn't it? 3/8th? How many straight and how many 90?
Co-Pang-Yang
Well-Known Member
- Posts
- 2,930
- Location
- Colchester, Essex
Well just got in from work gonna shower and head down the barn to put the disco back together and hopefully get the trailer repaired. Fun times.
mikeyt
Active Member
- Posts
- 299
mikeyt
Active Member
- Posts
- 299
6x90deg
Co-Pang-Yang
Well-Known Member
- Posts
- 2,930
- Location
- Colchester, Essex
I'll try and get down there if I have enough time.
antk
Member
- Posts
- 52
- Location
- harlow, essex
Where is the meeting point for tomorrow's lanning then and what time?
Brian S
Well-Known Member
- Posts
- 2,886
- Location
- Braintree, Essex
Well braintee McDonald is central and perhaps we can do the dunmow ford on the way.
antk
Member
- Posts
- 52
- Location
- harlow, essex
What time u getting there for?
Similar threads
