Engine seized?

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Now I see what you mean about the starter. Yes, the starter is fine. I'll have a look tomorrow and see if I can turn the engine over by hand.
 
If it struggles take the head off and using your finger put oil on the side of the bores it won't do any harm. It will ease the piston so it can move. Don't soak it but don't be shy.
 
Fluid in one bore above the piston is enough to cause a hydrolic lock,with glow plugs out try turning engine over, keep well clear of motor as any fluid will be ejected with some force.If this the case its likly head gasgit has gone.
 
Thanks for all your replies.
Still not cranking without the glow plugs, so I took off the head and put some oil down the bores, as suggested. Still no luck. Is there anything else I can try before I tow it to a mechanic?
 
instantsquid said:
So it won't turn with the clutch depressed and a socket on the end of the crank? Doesn't sound good :(

You did try to turn it clockwise didn't you?
Click to expand...
Turned it clockwise, and as I said, it won't crank with the starter connected either. I've had the head off and there is no foreign material in the cylinder. I wasn't exactly chavving around last time I used it so I can't see it being a blown engine...
 
Pour loads of oil down the boar so it covers the piston and comes up the bore .5mm and leave a few hours to seap through then turn by hand. Use the longest bar you have (breaker bar 1/2 inch) and put anothe extension on the end for extra leverage.
If this don't work it's a rebuild job or new lump job.
 
cambolt said:
Turned it clockwise, and as I said, it won't crank with the starter connected either. I've had the head off and there is no foreign material in the cylinder. I wasn't exactly chavving around last time I used it so I can't see it being a blown engine...
Click to expand...


This is probably gonna earn me nob of the week (except I think that title got awarded to some one earlier today :rolleyes: )

But is there any reason why trying to turn it counter clockwise wouldn't be a good idea. ( I'm assuming though that the siezure is being caused by something having come adrift in the block :eek: )
 
I had a similar problem a while back, when my 300 tdi 'appeared' to be siezed, it turned out to be that the Alternator had siezed, and was stoppimg the whole thing from turning over!
Might be worth looking at it?
 
Thanks for your replies everyone. So I towed it to the mechanic yesterday to have a look. He took one look at it and told me to come back in a few hours. So I did, and when I came back the news wasn't good. Apparently, one of the connecting rods had previously been replaced with a duff unit, and had broken, gouging out some of the crankcase (not all the way through though). I find this really confusing though, since the last time it was used was just a trip down to the corner shop, and I wasn't redlining it or anything (not that there is a redline anyway). And as I said before, it sounded fine when I turned it off, though I wasn't really concentrating. So the only cause I can see of this is if the conrod broke at the exact moment I turned it off, or if some bastard stole my motor and went joyriding :confused:
 
When you came back to it to find it wouldn't start - did it turn over even a little bit? That could have been the point at which the con-rod went. Seems incredible to me too - but I can't imagine that it broke just as you switched the engine off.
 
You must log in or register to reply here.

Similar threads

L
Intermittent starting issue.
Replies
4
Views
409
Anaconda
A
N
Defender TD5 - crank bit won’t start
2
Replies
21
Views
1K
sierrafery
sierrafery
N
Stater motor
Replies
5
Views
424
dag019
dag019
Globetreka
300Tdi or Td5?
Replies
2
Views
230
tottot
tottot
Flossie
Old car electrical question.
Replies
2
Views
731
J_D
J_D
Back
Top