Mcclegend
Well-Known Member
- Posts
- 1,349
- Location
- West Cumbria
I haven't got my defender yet and I'm so confused already about adding a second battery. I've done a search but no post seem to answer my questions.
Sorry it's so long but I'm just confused.
From what I can tell there are 5 main methods (there might be more that I haven't come across yet) for installing a dual battery system but each have there floors and disadvantages.
1. Run 2 alternators
Advantages, complete seperate circuits no worrys about running the start battery down at all due to relay problems. If start battery fails can manually use jump leads to join them together to get the Landy started. Can run 2 different types of batteries deep cycle, starter, lead acid, agm, etc without any problems. The Ah size of the batteries don't have to be the same.
Disadvantages, you need to install seperate altinator run cables, etc.
2. Ignition fed really, install a rely off the ignition switch that simply joins the two battery together when the ignition is on.
Advantages, simple to fit will isolate both battery's when the ignition is off saving the starter battery.
Disadvantages, not really idea to run different types of batteries or different sizes, soon as the ignition is switched on the weaker battery will start to draw power from the stronger battery, even when the engine isn't running.
3. Run two batteries in parallel.
Advantages, simplest thing to install and fit just join +ive to +ive and -ive to -ive job done, double the amount of power available.
Disadvantages, batteries should ideally be identical size and type, no protection for starting, if one battery develops a broken cell it will drag the other battery down with it.
4. Voltage sensing rely.
Advantages, cheap, easy to fit, isolates start from second battery, can manually use jump leads.
Disadvantages, again batteries should ideally be identical size and type this cause problems when wanting to run things over night due to not being a deep cycle battery. If the secondary battery is extremely low it will receive charge from both the start battery and the alternator until both batteries equalise in voltage then both will charge, this could (theatrically) on short runs drain the start battery.
5. Dc to dc chargers ( battery management system).
Advantages, easy to fit can run different types and sizes of batteries, full isolation of starter battery, can jump lead them together.
Disadvantages, expensive.
The other question is what sort of battery type to use as the secondary battery, starter battery or deep cycle.
Starter battery's should only be taken down to 80% charge.
Deep cycle depending on make can go down to 20% to 50% charge. If going deep cycle, 12v battery or 2 x 6v batteries in series.
Then what sort of battery, lead acid, agm, calcium, all prefer different charging voltages.(I read somewhere)
I know there is people on here that will say you can run different types and sizes with each other and you can but they won't last as long (but does this matter in the long run), I've seen three set up's fail, I can't confirm that it was due to different sizes or types but they haven't failed since we got dc to dc charges installed on two of them and installed two identical batteries on the other. (Boat and two motor homes)
I might be over thinking things (probably am) but the more I look into it the more questions are raised.
If any one could shed light if I'm missing something on one of the methods that might tilt things in that ways favour or I've miss understood something I've read and pieced together.
Sorry it's so long but I'm just confused.
From what I can tell there are 5 main methods (there might be more that I haven't come across yet) for installing a dual battery system but each have there floors and disadvantages.
1. Run 2 alternators
Advantages, complete seperate circuits no worrys about running the start battery down at all due to relay problems. If start battery fails can manually use jump leads to join them together to get the Landy started. Can run 2 different types of batteries deep cycle, starter, lead acid, agm, etc without any problems. The Ah size of the batteries don't have to be the same.
Disadvantages, you need to install seperate altinator run cables, etc.
2. Ignition fed really, install a rely off the ignition switch that simply joins the two battery together when the ignition is on.
Advantages, simple to fit will isolate both battery's when the ignition is off saving the starter battery.
Disadvantages, not really idea to run different types of batteries or different sizes, soon as the ignition is switched on the weaker battery will start to draw power from the stronger battery, even when the engine isn't running.
3. Run two batteries in parallel.
Advantages, simplest thing to install and fit just join +ive to +ive and -ive to -ive job done, double the amount of power available.
Disadvantages, batteries should ideally be identical size and type, no protection for starting, if one battery develops a broken cell it will drag the other battery down with it.
4. Voltage sensing rely.
Advantages, cheap, easy to fit, isolates start from second battery, can manually use jump leads.
Disadvantages, again batteries should ideally be identical size and type this cause problems when wanting to run things over night due to not being a deep cycle battery. If the secondary battery is extremely low it will receive charge from both the start battery and the alternator until both batteries equalise in voltage then both will charge, this could (theatrically) on short runs drain the start battery.
5. Dc to dc chargers ( battery management system).
Advantages, easy to fit can run different types and sizes of batteries, full isolation of starter battery, can jump lead them together.
Disadvantages, expensive.
The other question is what sort of battery type to use as the secondary battery, starter battery or deep cycle.
Starter battery's should only be taken down to 80% charge.
Deep cycle depending on make can go down to 20% to 50% charge. If going deep cycle, 12v battery or 2 x 6v batteries in series.
Then what sort of battery, lead acid, agm, calcium, all prefer different charging voltages.(I read somewhere)
I know there is people on here that will say you can run different types and sizes with each other and you can but they won't last as long (but does this matter in the long run), I've seen three set up's fail, I can't confirm that it was due to different sizes or types but they haven't failed since we got dc to dc charges installed on two of them and installed two identical batteries on the other. (Boat and two motor homes)
I might be over thinking things (probably am) but the more I look into it the more questions are raised.
If any one could shed light if I'm missing something on one of the methods that might tilt things in that ways favour or I've miss understood something I've read and pieced together.
Last edited: