doors

beakerthemuppet · Dec 17, 2006

Hello

Had my first Series 3 SWB landy for 2 weeks now and I am having problems with the doors: they don't seem to shut properly.

They catch on the first part of the catch but don't seem to engage on the second proper part of the catch. I have tried moving the catching plate thing closer but it has made no difference. They don't seem to shut even with a large amount of force and body weight pushing them!!

Any advice on how to make the doors shut properly? Do the hinges need adjusting?

Thanks

Beaker

Spyderman · Dec 17, 2006

Mine is the same but they shut OK with a good slam.

clivees · Dec 17, 2006

Mine too after a put new door rubber on.
I just slam them now.

pricey · Dec 17, 2006

put a tad of oil or grease on the latch and catches mine shut a treat after that

yella · Dec 17, 2006

i thought they were all like that, yer know, the old landrover build quality syndrome

Wesley Pegden · Dec 17, 2006

beakerthemuppet said:
Hello

Had my first Series 3 SWB landy for 2 weeks now and I am having problems with the doors: they don't seem to shut properly.

They catch on the first part of the catch but don't seem to engage on the second proper part of the catch. I have tried moving the catching plate thing closer but it has made no difference. They don't seem to shut even with a large amount of force and body weight pushing them!!

Any advice on how to make the doors shut properly? Do the hinges need adjusting?

Thanks

Beaker

I had this problem on my old series 2, tried allsorts to start with including moving the striker plate about and fannying about with the door rubbers etc. The problem was the door handle mechanism, it was as dry as a witches tit. Take yer door card off (thats if yerv got one) and spray inside the door handle mechanism with WD40, absolutely soak it and you should be OK at that.

Regards WP.

beakerthemuppet · Dec 17, 2006

spray inside the door handle mechanism with WD40, absolutely soak it

Thanks for the tips, I have tried this and the doors still not shutting.

They just don't seem to get close enough for the catch to go over the second lip of the lock bit on the door pillar. Its as though they are stuck on something but I can't find anything in the way!!

I think that I will take the door tops off over Christmas and see if that make a difference (no idea why it should but I have tried nearly everything else) and if that doesn't then the doors are off and I will try to rehang them.

I am coming to the conclusion that they may be slighly bent but it would be odd if it was both doors wouldn't it?

Any more tips or similar experiences welcomed.

Thanks

beaker

stig · Dec 17, 2006

Instead of sending the striker plate inwards bring it right out, then shut the door and make sure that it going onto the second catch if that works bit by bit move the striker in until you get to the point that it will not operate on the second latch and back it back a bit (this is the way that I was taught when serving my time as a panel beater 34 years ago). If this is still not working your door may be to far in at the front causing the door to "stop" before it is meant to and you are then bending the door to try and close it. Hope this helps, Barry

Trewey · Dec 17, 2006

My doors shut fine at the bottom, but there's a half inch gap at the top - I thought this was normal! The Doris moans about the draught though.

slob · Dec 17, 2006

sounds like ma noo hoose door

GRUNT · Dec 18, 2006

Ey up I've got a noo hoose door.

Any old how are you sure the problems with the door bit of the catch, have a look at the frame to see if it has bent backwards and inwards taking the catch with it. There's a stiffener plate that goes back to the rear bulkhead that could have bent out of shape.

ormus · Dec 18, 2006

correct door fitting is an art form. ive known pukka panel beaters spend hours doing it properly. as much as a whole day to fit 4 doors.

maxcribbin · Dec 19, 2006

Give ur striker plate a new lease of life using a grinder!
Use a bit of wd40 and a good old slam!

Mine used to catch on the 1st bit and open when i went off roading!

Carl.

ormus · Dec 19, 2006

now you know why, we used to bolt/weld the doors up, on the grass track minis.

beakerthemuppet · Dec 19, 2006

Use a bit of wd40 and a good old slam!

Tried the WD40 and the slamming, in fact all sorts of slamming - the slow then quick slam, the full on slam, the slam then hip shove - all no good, the catch won't go over the second part of the striker plate and the striker plate has been moved as close to the door as it can be.

I think that I will take the doors off over Christmas and see if attempting to rehang them solves the problem. I know that it is not a major thing but it is bugging me becuase I think that there is a simple solution but I can't find it.....yet!!

thanks

beaker

doors

beakerthemuppet

New Member

Spyderman

New Member

clivees

Well-Known Member

pricey

Active Member

yella

New Member

Wesley Pegden

Well-Known Member

beakerthemuppet

New Member

stig

New Member

Trewey

Cockernee, Pasty munchin bastid.

slob

Well-Known Member

GRUNT

Well-Known Member

ormus

New Member

maxcribbin

Banned

ormus

New Member

beakerthemuppet

New Member

Similar threads