Discovery Rust - Boot, Sills and Wings

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
gummy bear said:
looks the mutz nutz mate.now stop messing and lets get it down waterlane :eek:
you have done a wicked job mate and you should be well chuffed with yourself.
Click to expand...

Thanks Mark, yeah I'm happy with it so far. Been checking today and I need the master cylinder replacing :( but won't take too long and then we can go and play - I promise :D
 
Redhand:

Well stuck woods sounds about right tbh, there was some serious trouble to be bad there. The other guys found a lane that they didn't even attempt, I didn't see it cos my lardy disco couldn't get up the hill, but I can quite imagine that guy getting stuck for 4 days. The mud was the greasiest clay I have seen. Only thing similar is the clay bog at the far corner of the parkwood site, nobody gets through there.

1spin:

The mess was collateral :D
 
LOOKS FANTASTIC! i lifted my boot lineing the day. the center plate its perfect but everything round it is brown dust. dont fancy doin mine? :D a can see the next few days being spent wellding the tits out of the thing!!
 
rustyzone a lyk that lol. theres not even any point putin a seat belt on in the thing coz the mounting points are f**ked. a think a need ti learn ti weld! lol
 
DA03RAE said:
LOOKS FANTASTIC! i lifted my boot lineing the day. the center plate its perfect but everything round it is brown dust. dont fancy doin mine? :D a can see the next few days being spent wellding the tits out of the thing!!
Click to expand...

Easiest way is spot drill the welds and then chequer plate. Cheaper and looks better plus you can always unscrew it to get to the tank. Learnt this from Mr Noisy.

Yeah rusty zone is about right.:D
 
GreenHornet said:
Ok this is my attempt to upload some descent photos of the Green Hornet. I hope it works.



d2b01676.jpg


4aa14c89.jpg
Click to expand...

Wonderful "toy" is obtained. :)
Good luck with your work.
Happy New Year to all, good health and good luck.

..... Fleet, this is close to Basingstoke, If we are lucky and come in summer, can drink a beer.:rolleyes:
 
Just have the brakes to sort and I am done. will try another bleed this weekend and see if that works while i wait for the Master cyclinder dosh. a bit tight after christmas tbh. Kids..........

I am quite excited to get her on the road as i am tired of the bike at the moment. it needs new pivot bearings and a service too...........

btw, where did you get the tube for your tree sliders from?
 
Last edited:
GreenHornet said:
Just have the brakes to sort and I am done. will try another bleed this weekend and see if that works while i wait for the Master cyclinder dosh. a bit tight after christmas tbh. Kids..........

I am quite excited to get her on the road as i am tired of the bike at the moment. it needs new pivot bearings and a service too...........

btw, where did you get the tube for your tree sliders from?
Click to expand...


Its cds tube and I got it off a mate also got him to put a 90deg bends on them as well, want me to find out how much?
 
You must log in or register to reply here.

Similar threads

G
Discovery 2 Wheel Arch Rust
Replies
19
Views
1K
Badger688
Badger688
S
Disco 1 Disco 1 Rust repair prep
2
Replies
20
Views
2K
sv_dOnut
S
D
Discovery 1 300tdi immobiliser
Replies
1
Views
254
Stanleysteamer
Stanleysteamer
alfapat
Vehicle pulls L/Right
Replies
6
Views
217
Nodge68
Nodge68
A
1995 Discovery 300TDI Engine Issue - Thoughts
Replies
2
Views
523
shaynecm
S
Back
Top