D1 prop issues
- Thread starter Fsob88
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 44,827
- Location
- East Dorset
"prop fell off" is a bit general, more specifics?
If it's just the rubbber flexi-joint and no other harm was done, you could just replace that, but if it went down the road too far and fecked itself up then sure, you need a new propshaft!
If it's just the rubbber flexi-joint and no other harm was done, you could just replace that, but if it went down the road too far and fecked itself up then sure, you need a new propshaft!
- Posts
- 44,827
- Location
- East Dorset
..."Bracket" Hmm!
The prop shaft has a rubber flexijoint on the end which connects to the flange of the diff pinion.
If the rubber fractures, the prop will drop. There is no bracket involved.
If you have not bent or otherwise harmed the prop shaft in anyway, you might get away with just replacing the rubber flexijoint, but if the prop hit other stuff, like the road or the underside of the vehicle, it may be distorted which will lead to vibration at the very least.
Take the prop off, and examine it very carefully for signs of abrasion and distortion. also check no balance weight has been knocked off.
If you are confident it is all OK then order and fit a new rubber donut.
The prop shaft has a rubber flexijoint on the end which connects to the flange of the diff pinion.
If the rubber fractures, the prop will drop. There is no bracket involved.
If you have not bent or otherwise harmed the prop shaft in anyway, you might get away with just replacing the rubber flexijoint, but if the prop hit other stuff, like the road or the underside of the vehicle, it may be distorted which will lead to vibration at the very least.
Take the prop off, and examine it very carefully for signs of abrasion and distortion. also check no balance weight has been knocked off.
If you are confident it is all OK then order and fit a new rubber donut.
- Posts
- 22,902
- Location
- In the next Glen
Too far away for me to help I have a spare new donut & propshaft.
I also have a spare new wide angle prop & 4 bolt flange to get rid of the dungnut.
I also have a spare new wide angle prop & 4 bolt flange to get rid of the dungnut.
Sorry guys I don't believe mine had the dounut I assume had been changed has a flexible uj both sides or supposed to
- Posts
- 44,827
- Location
- East Dorset
Sorry, is yours a V8?
If a 300tdi should have had a rear prop with ordinary U/J to transfer box and rubber donut to rear axle, if a V8, imsc, an ordinary U/J to both ends.
Does that help?
If a 300tdi should have had a rear prop with ordinary U/J to transfer box and rubber donut to rear axle, if a V8, imsc, an ordinary U/J to both ends.
Does that help?
- Posts
- 44,827
- Location
- East Dorset
Not a bad thing to do at all, I would prefer mine to be like that!
So, can you just change the U/J?
- Posts
- 44,827
- Location
- East Dorset
You need someone who can quote you a part number for that, and the O ring. Hopefully someone will jump on with the info you need.
Gazbo
Well-Known Member
- Posts
- 3,949
Sounds like a uni needle bearing cup has lost it's retaining circlip and the trunnion, cross piece has popped out. If you're lucky just a bit of clean up of flange bearing cup bores and a uni joint kit will fix it.
Gazbo
Well-Known Member
- Posts
- 3,949
Not quite correct, the rubber donut type has a central guide bush in the diff end of the driveshaft/prop shaft and a ball ended guide pin into the diff mounted three legged flange on the diff, so what will normally happen if the donut fails is the driveshaft/propshaft will stay on centre with the metal arms and bolt heads coming together to continue drive, albeit noisily. Had it happen on my first Tdi, shaft will not drop out.
But that doesn't help this guy, sounds like his has been converted to both end Uni joints.
- Posts
- 44,827
- Location
- East Dorset
Hi Gazbo, I understand exactly what you say and yes the central guide bush was an absolute
sod to get off. I confess the first time I changed the rubber donut, I just left the old guide bush in. The second time I did change it after a struggle. Confess I still do not know what OP meant by a "bracket" and yes sounds like he's got two u/js.
- Posts
- 44,827
- Location
- East Dorset
Sounds like what he meant. Agree totally and hope there is enough metal left for the circlip to stay in!
