Clunking noise

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
When the car is coasting it won't make the noise only when u put ur foot down, or when it's really underload say going up a steep incline will it make the noise, it definitely sounds like it's from the front and more so the drive train cheers
 
simonmorgan said:
When the car is coasting it won't make the noise only when u put ur foot down, or when it's really underload say going up a steep incline will it make the noise, it definitely sounds like it's from the front and more so the drive train cheers
Click to expand...


Shot diff is more like grinding noise, never heard one clunking, could you record and utube it?
 
I would go for a failing diff. Mine did a similar clunk, skip when you hit the accelerator from coasting, ok on gentle acceleration......which soon turned into a constant grinding noise from the rear diff.

PS. both my props have UJ's both ends.
 
martynv8 said:
I would go for a failing diff. Mine did a similar clunk, skip when you hit the accelerator from coasting, ok on gentle acceleration......which soon turned into a constant grinding noise from the rear diff.

PS. both my props have UJ's both ends.
Click to expand...

Is yours a manual? Diesel manual rear props should have U/J both ends. Auto rubber at front U/J at rear.
 
Hi everyone yes there is vibration coming from the gearbox tunnel when u put it foot down, if u rev it at a standstill there is no noise at all, what parts are serviceable on the front prop as I just changed the uj's I never checked anything else ?
 
simonmorgan said:
Hi everyone yes there is vibration coming from the gearbox tunnel when u put it foot down, if u rev it at a standstill there is no noise at all, what parts are serviceable on the front prop as I just changed the uj's I never checked anything else ?
Click to expand...

You did tighten it up i suppose.
 
Yes get under there again check all bolts did you use a propshaft tool of fiddle about with two spanners the tool makes like easier and more reliable ie less tired arms.

While your under there and you have the car jacked up so that you can turn the prop shaft with a wheel so its not binding ie free movement check both ends again and don't forget the front prop has a sliding joint check that too for play it too has a grease nipple the front section with the uj attached the short section should face engine .

Gl
 
Grit Valve said:
Yes get under there again check all bolts did you use a propshaft tool of fiddle about with two spanners the tool makes like easier and more reliable ie less tired arms.

While your under there and you have the car jacked up so that you can turn the prop shaft with a wheel so its not binding ie free movement check both ends again and don't forget the front prop has a sliding joint check that too for play it too has a grease nipple the front section with the uj attached the short section should face engine .

Gl
Click to expand...

Cheers mate will take it off again and double check, I used spanners to tighten the bolts (all new bolts too) if it has play is it a case of a new prop shaft ?
 
simonmorgan said:
Cheers mate will take it off again and double check, I used spanners to tighten the bolts (all new bolts too) if it has play is it a case of a new prop shaft ?
Click to expand...

It should slide smoothly and if it can wobble its worn but it be could be stiff also due to rust,dried grease or even no grease ect

So just recheck it over again best to be sure
If bad then yes as both parts would be worn the front part has splines that locate into the rear section .
 
You must log in or register to reply here.

Similar threads

ar1g3
P38A P38 rattle at idle
2
Replies
26
Views
3K
roythebus
R
p38DH
P38A Diagnostic device
Replies
8
Views
1K
p38DH
p38DH
B
Rear rattle/ clunking
Replies
4
Views
245
Anaconda
A
H
Freelander 2 whining
Replies
2
Views
422
HWel
H
S
Engine tickinh noise
Replies
0
Views
458
Shore968
S
Back
Top