Classic temp guage clocks sender or head
- Thread starter Bern768
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
I'm not even sure if it's the right dash or not it's been messed about with a lot it's an 85 so think it should have the early dash in, and it originally didn't have a thermostat in have since put one I haven't taken it on a long journey as didn't want to cook it but sits about 3/4 most of the time and starts to creep up on a hill but not gone into the red , heaters etc stay warm so hasn't blown any water out
Ok so.
The car never had a thermostat when you got it, as the PO converted it ?
You put in the thermostat and now it reads high?
I don’t know what dash it should or shouldn’t be, but both engines have different sensors.
If in doubt buy a cheap standalone temp sensor/gauge to check.
J
The car never had a thermostat when you got it, as the PO converted it ?
You put in the thermostat and now it reads high?
I don’t know what dash it should or shouldn’t be, but both engines have different sensors.
If in doubt buy a cheap standalone temp sensor/gauge to check.
J
Yes po had done it everything that had been done was horrendous I basically had to rewire everything as it was all very temperamental or lucky if it worked at all, but before I put a stat in it would read about 1/4 or to a half up a long hill but the heating was only ever just warm which leads me to think it's more of a gauge or sender problem or wrong match attached is Po's attempt at the engine harness so obviously was all to a good standard lol
Attachments
I think for the sake of few quid certainly worth doing then even once I've figured it out I will always have a backup reading
Hicap phill
Well-Known Member
- Posts
- 16,242
- Location
- Wiltshire
Now this sounds mad….
Take a photo of the location on rear panel where the fuel cap/cover is
Take a photo of the location on rear panel where the fuel cap/cover is
discool
Well-Known Member
- Posts
- 13,609
Looks similar to the dash that my 1987 3.5 so an EFI other than mine was MPH.
As you have a 300 Tdi engine fitted so you require a coolant temp sensor part no. AMR1425 indicated by a green band.
Thermostat if interested is ERR2391.
The range rover dash illuminated indicators are self explanatory.
There you go good sir
Attachments
I will have a look at the temp sender see what it is stat is new and 88 degrees can't remember what the part number was but have got all the relevant warnings etc to work
- Posts
- 12,628
- Location
- Sud ouest France !
Unplug the sensor on the engine and see if you get a reaction on the clocks lar 
Hicap phill
Well-Known Member
- Posts
- 16,242
- Location
- Wiltshire
You can tell years by where the filler is.Your mad
But hey join the club
J
That’s late 80”s so would have been v8( unless 2 battery trays then a VM diesel)
I did confirm there was the 4x4 logo/light on the dash as they used the same in maestro cars
And @discool has confirmed the part number
Yes was originally a V8 it's an 85 exposed hinge one , but is well butchered before I got my hands on it
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
Is the sensor a single wire or two wire device? If single, try clipping an earth wire to the sensor body.
discool
Well-Known Member
- Posts
- 13,609
My disco runs just ‘north’ over the central line, as your gauge also runs just over the central line, being west as its a horizontal display
If it stays that way like mine its not an issue.
Same dash as my '86 EFi except mine too is in MPH.
Notwithstanding the LRcat part numbers if you check Rimmers you will see several stats listed for the Classic V8.
They show the 88deg for 'cold climates' an 82deg as 'standard' and a 74deg for 'hot climates'.
FWIW an 88 in mine (CA chassis) shows the needle much where yours is & an 82 puts it pretty much in the middle or very slightly above.
Notwithstanding the LRcat part numbers if you check Rimmers you will see several stats listed for the Classic V8.
They show the 88deg for 'cold climates' an 82deg as 'standard' and a 74deg for 'hot climates'.
FWIW an 88 in mine (CA chassis) shows the needle much where yours is & an 82 puts it pretty much in the middle or very slightly above.
Similar threads
