Brake problems

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
A

aidenV8disco1

New Member
Posts
4
Location
Fareham
Hi guys, I have a Disco 1 v8 92,

I had spongy brakes so I bleed the system and not a lot changed. Ive look on different forums and they say reservoir leaking or full with crap,


So I’ve ordered and master cylinder and reservoir kit witch I’ve changed and cleaned out, then I also changed the pads and re-bleed the system, all crap came out of pipes and flowing well,


The peddle seemed to harden up and feel fine until I started up the engine and it went back to being spongy any advice or help would be great full


Cheers

Aiden
 
It will go a bit spongy when engine is running, it’s the servo doing its job, it’s best to bleed the front callipers by using a bleed pipe with three connections, basically bleed all nipples on the calliper at once, that way you are more certain to get all the air are out,
I also replaced all my flexible pipes with Goodrich stainless braided pipe they also make the pedal firmer,
 
Europa486 said:
It will go a bit spongy when engine is running, it’s the servo doing its job, it’s best to bleed the front callipers by using a bleed pipe with three connections, basically bleed all nipples on the calliper at once, that way you are more certain to get all the air are out,
I also replaced all my flexible pipes with Goodrich stainless braided pipe they also make the pedal firmer,
Click to expand...


Thank you I’ll have a go with that. But also the pedal goes all the way to the floor with not a lot of braking

Cheers
 
Could well be the master cylinder, I know it’s new but could still be faulty, when you pump the pedal when bleeding
Are you getting a good amount of fluid with each pump? If not then it’s likely the Master cylinder is faulty,
I would only use genuine or OE for brake parts,
I take it you have no leaks anywhere? I replaced my pistons and seals on the callipers when I overhauled the system,
 
Europa486 said:
Could well be the master cylinder, I know it’s new but could still be faulty, when you pump the pedal when bleeding
Are you getting a good amount of fluid with each pump? If not then it’s likely the Master cylinder is faulty,
I would only use genuine or OE for brake parts,
I take it you have no leaks anywhere? I replaced my pistons and seals on the callipers when I overhauled the system,
Click to expand...

yes it comes through fine, and no I can’t see any leaks though out the whole system
 
Then another good bleed with new fluid ( don’t use the old) start with rear n/ s then rear O/s
Followed by n/s front then lastly o/s front, use the three pipes for the front and it should be good,
New pads until bedded in will also make the pedal softer,
The reason you don’t reused fluid even if it’s new is it will contain Minuit air bubbles, so would need to be left standing for a day or so,
 
Does soudn mcyl related, but Iirc the early D1 had a concentric mcyl pushrod set up, ie it might ot be set up correclty?
Do not ask me how to set it up, I have no idea! assume just a knatts cock free play?
 
lynall said:
Does soudn mcyl related, but Iirc the early D1 had a concentric mcyl pushrod set up, ie it might ot be set up correclty?
Do not ask me how to set it up, I have no idea! assume just a knatts cock free play?
Click to expand...

No the brake master just bolts straight to the servo unit so doesn’t need adjustment,
The clutch master has the concentric adjustment, very easy to adjust, just rotate the through bolt
Until it’s in line with the brake pedal,
 
You must log in or register to reply here.

Similar threads

Lej
Discovery 2 Clutch failure
Replies
2
Views
630
Lej
Lej
Neptune1922
Disco 2 No Brakes of almost no brakes.
2
Replies
32
Views
2K
Neptune1922
Neptune1922
F
V8 Idle & Brake Pedal issue - combined???
Replies
1
Views
240
discool
discool
P
Discovery 2 brake issues after replacment
Replies
4
Views
718
psk100
P
L
Disco 2 brake question
Replies
5
Views
629
landynutterme
L
Back
Top