Millertime_9
Active Member
- Posts
- 223
- Location
- Glasgow
Boot door missing bolt?
- Thread starter Millertime_9
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
I am no expert, in-fact I logged on to ask if anyone knows where to buy stainless steel front and back mud flap bolts for my 90......
but it looks like a bolt head had sheered of (a long time ago) judging by the rust... same thing happened to my old 110 on the rear passenger door stay looked identical but with less rust.. just done a quick google. can't tell if this is a botch job or for real, does yours look like it may have a hole through it?
but it looks like a bolt head had sheered of (a long time ago) judging by the rust... same thing happened to my old 110 on the rear passenger door stay looked identical but with less rust.. just done a quick google. can't tell if this is a botch job or for real, does yours look like it may have a hole through it?
sierrafery
Well-Known Member
- Posts
- 18,259
- Location
- Arad/Romania
You need 3 new parts there, google out as follows:
1. MXC1087
2. BYF100070
3. BYV100000
These are parts 9, 10, 18 http://new.lrcat.com/#!/1232/35775/35776/2739/36142
1. MXC1087
2. BYF100070
3. BYV100000
These are parts 9, 10, 18 http://new.lrcat.com/#!/1232/35775/35776/2739/36142
Millertime_9
Active Member
- Posts
- 223
- Location
- Glasgow
darrenm
Active Member
- Posts
- 670
- Location
- Chorley Lancashire
How do you remove the old one
sierrafery
Well-Known Member
- Posts
- 18,259
- Location
- Arad/Romania
What's certain is that has circlip at the bottom too and you have to remove that so do somehow to reach it(i can't tell you how)
discool
Well-Known Member
- Posts
- 13,709
As it appears that due to the lack of any lubricant you have a bit of long term rust in the area of the clevis pin. Answer With difficulty.
So to remove the clevis pin soak it with PlusGas overnight and then hit squarely with a club hammer, if your lucky in will move and drop out below the bumper.
The new pin will be installed from below with one of the clips fitted, the second clip will then be fitted to retain the door stay.
The clevis pin that a Defender has, although similar it may not be the same, it has a mushroom head so only uses a clip above the bumper to retain the door stay.
If the pin doesn’t move, then there’s a modification thats stated on on the web, so depending on you engineering skill, drill a hole in the top of the existing pin in situ, then tap thread into it for a screw, then with a large washer and with the suitable screw plus a small washer to retain the the large washer on top of the stay... job done.
darrenm
Active Member
- Posts
- 670
- Location
- Chorley Lancashire
I cannot see any way to get it out all underneath is solid so cannot see the other side
darrenm
Active Member
- Posts
- 670
- Location
- Chorley Lancashire
I cannot see anyway for it to drop out or access it from underneath
kevinrbeech@msn. com
New Member
- Posts
- 5
- Location
- Bournemouth
Mine (back in 2004) was like that too, I eventually drilled the stud and put in a split pin with a washer under, that lasted until the back end fell off due to rust.
Lovely vehicle though, 200 tdi, bought on 143k sold on 223k, took it to Tunisia 3 times, spent a fortune on it but best car I ever had, until now.
Now I got a D3 with less than 100k on the clock, thinking of taking that to the desert now.
Lovely vehicle though, 200 tdi, bought on 143k sold on 223k, took it to Tunisia 3 times, spent a fortune on it but best car I ever had, until now.
Now I got a D3 with less than 100k on the clock, thinking of taking that to the desert now.
- Posts
- 13,797
- Location
- The Principality
My D2 did that so my mechanic welded a large 'washer' into the top of that bolt head.
darrenm
Active Member
- Posts
- 670
- Location
- Chorley Lancashire
That’s what I did today
