- Posts
- 9,105
- Location
- Roaming the UK on assignments
Getting there mate, I've put off starting mine until tomorrow 
What black is that?
What black is that?
Big Stripdown and Weld thread 300tdi
- Thread starter Chrisw8
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
It’s Manor Chassis Black.
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
Thought I’d clean up some nut threads ... tapped and bunged bolts in covered in copper slip.
Having trouble with this one ....well 3 actually, anyone know what size thread it is , or what bits go onto it ? Could it be imperial ?
12mm seems too big and 10mm is too small.
Anyone says 11mm and I’ll come round and nut them !!!
Will spend all evening going through my phone photos to see what I took off there.
Having trouble with this one ....well 3 actually, anyone know what size thread it is , or what bits go onto it ? Could it be imperial ?
12mm seems too big and 10mm is too small.
Anyone says 11mm and I’ll come round and nut them !!!
Will spend all evening going through my phone photos to see what I took off there.
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
Suppose piccy would help .....
neilly
Well-Known Member
- Posts
- 20,000
- Location
- Oxfordshireness
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
Think you will find they are Metric fine Chris
+ its a seat belt anchor
+ its a seat belt anchor
- Posts
- 9,105
- Location
- Roaming the UK on assignments
I thought they were 7/16 UNF for the dicky seats?
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
Amazing wot you find in yer phone pictures.....found this chappie on our back wall , I gave it a kiss and .......
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
D/D69 is probs right on the thread
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
Fk it. I’ll find the bolts and walk them back through.
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
WACK......poxy spell checker!!!
- Posts
- 9,105
- Location
- Roaming the UK on assignments
Unless you're fitting the seats you could epoxy a bung in there just to seal the holes up.
I would have plug welded them over unless I was fitting the dickies back in there.
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
If you wont to clean the threads out Chris get 1 of your bolts & with a slicing disc & cut into the end of the bolt then re leave 2 sides to make it look like a tap & you can use to clean ALL the other seat belt mount threads & save that bolt till last
& you can use to clean ALL the other seat belt mount threads & save that bolt till last
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
Probably won’t fit dickies back in, but like to keep options open.
Maybe I’ll bung some seam sealer in there.
Maybe I’ll bung some seam sealer in there.
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
If you wont to clean the threads out Chris get 1 of your bolts & with a slicing disc & cut into the end of the bolt then re leave 2 sides to make it look like a tap
Are all seat belt bolts the same size then .?
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
They are on your motor & probs the same in all motors
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
Aha.
Off to have a look on microcat site.
Off to have a look on microcat site.
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
indeed, certainly a labour of love !!
Similar threads
