Best way to cut van back roof and sides
- Thread starter warrior
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Maybe something like this?
Dewalt Dt1206qz Trimsaw Blade 165 X 20mm X 36t For Aluminium Dc390, DEWDT1206QZ at D&M Tools
Dewalt Dt1206qz Trimsaw Blade 165 X 20mm X 36t For Aluminium Dc390, DEWDT1206QZ at D&M Tools
- Posts
- 7,877
- Location
- East Midlands
Those teeth might turn out to be a wee bit coarse for cutting thin sheet. Is there anything a bit finer on offer anywhere?
Not that I've seen that was just a quick look tho. Maybe something like a cutting disc for a grinder if I could find one the right size, well correct bore overall width could go down if needed.
blue beasty
Leaks an prone to bits dropping off
- Posts
- 63,106
- Location
- Gloucestercotshirewolds
I'd go for careful marking, a steady hand and a thin cutting disk.
I'd say a circular saw was too coarse and powerful and a jigsaw prone to the blade wandering off 90 degrees when cutting through channels.
I'd say a circular saw was too coarse and powerful and a jigsaw prone to the blade wandering off 90 degrees when cutting through channels.
tyre man dave
Active Member
- Posts
- 734
- Location
- redcar cleveland
a plasma cutter should cut it easy
if you know of anyone who has one.
or 1mm cutting disc in grinder just as good
if you know of anyone who has one.
or 1mm cutting disc in grinder just as good
bluedog333
Well-Known Member
- Posts
- 5,442
- Location
- Henley on Thames, Oxfordshire
A multi-cutter will do a good job, less destructive than a grinder or saw. Bosch make a reasonably priced one, Fein are the daddy, but ruddy expensive!
bluedog333
Well-Known Member
- Posts
- 5,442
- Location
- Henley on Thames, Oxfordshire
Your dad sounds like an ideal dad! I've raided my parent's shed and came away with 2 rusty screwdrivers.
There's alsorts, tools for every building trade and lots of snap on tools and other stuff like a mini digger and hydrolic log spliter to name a few. And alot of my crap
vilguy
Do'er of stuff and the like
- Posts
- 9,915
- Location
- Dumfrieshire
ive a circular saw blade on my bench saw which cuts through thin sheet lovely,
I wouldnt use a jigsaw
Im with bb - thin slitting disc and careful marking
I wouldnt use a jigsaw
Im with bb - thin slitting disc and careful marking
wickford90
Well-Known Member
- Posts
- 3,623
- Location
- wickford essex
When I cut windows in I put on wide masking tape and drew my lines on that. measured everything twice and used a 1mm blade in grinder. Went through a treat.
tyre man dave
Active Member
- Posts
- 734
- Location
- redcar cleveland
plasma cutter is the way to go
first check on a scrap piece or alloy
make sure it cuts it, and not melts it
some plasma cutters are not designed for cutting alloy
first check on a scrap piece or alloy
make sure it cuts it, and not melts it
some plasma cutters are not designed for cutting alloy
v8geoff
Well-Known Member
- Posts
- 3,327
- Location
- chippenham,wiltshire
Recip saws are brilliant used mine to extend my arches just need steady hand
vilguy
Do'er of stuff and the like
- Posts
- 9,915
- Location
- Dumfrieshire
They will cut pretty much anything conductive matey.
Thor1950
Well-Known Member
- Posts
- 39,238
- Location
- Land of the midnight sun
a very fine blade put in backwards cuts very nice. There are several youtubes available to watch
