BennehBoy's D2 adventure

Bennehboy · Nov 15, 2014

Reassembled the head:

Hydraulic followers in:

Cam cover coated in proper sealant, masked off the edges where the cam sits to stop it being squeezed onto the cam with clamping pressure:

Journals & followers oiled, camshaft dropped in with timing at roughly TDC:

Cam carrier fitted - the rocker has to be fitted on top and the 6 bolts torqued down to 32nm radiating out from the centre, this compresses all the springs and gives a nice fit before torqueing the remaining 13 bolts down to 25nm:

Just needs the EUI adjusters doing once fitted to the block now.

Bennehboy · Nov 30, 2014

Cylinder head swap cracked on with!

Rocker cover off, and there's some nasty grime stuck to the underside, the oil is NOT in good condition at all - that said the cam is in great condition so no the filters are doing their job:

Dropped the oil and coolant, removed the turbo, top hose, intercooler hoses, front cam cover off, wiring loom disconnected and fed back through inlet manifold, timing set to TDC and pins inserted, head bolts out, timing sprocket tied to chain, chain tensioner out, vac pump oil feed out, various nuts n bolts off:

Mmmm pizza...

Just need to disconnect the FPR feeds and it can be lifted off:

Most important tool is on the stepladder (I'm 6 foot and still can't reach without the back of the bay easily without a ladder!).

jamesmartin · Nov 30, 2014

thats a dirty engine ,has it done many miles since oil change

Bennehboy · Nov 30, 2014

jamesmartin said:
thats a dirty engine ,has it done many miles since oil change

About 5-6K

Bennehboy · Nov 30, 2014

Head coming out:

HG looks fine (it's only been on for 5K miles!):

Underside of duff head looks ok still:

Pistons look fine:

Block deck is pretty clean:

Manifolds and FPR removed from old head:

Harness out, should fit new, but will see how this one goes:

Heatplugs out of new head, they are Beru but were a bit 'wobbly', swapped in the 5k old ones in from the old head:

Turners cocked up again and sent the wrong FPR gasket, they did this last time, you can see 'early' written on the bag but they send a 15P type, ffs, will have to re-use the old gasket:

Replacement head built up, the AMC heads are a LOT heavier than the stock one:

New HG on:

Head lifted on:

Refit is the reverse of removal....

Apart from new top hose:

Injector asdjusters all done:

Oil in, coolant in, fuel rail purged twice, but it won't start

Watch this space...

Bennehboy · Nov 30, 2014

jamesmartin said:
thats a dirty engine ,has it done many miles since oil change

And this is why the head is being replaced, the oil is coolant contaminated, that's why the head looks so filthy, the oil/coolant mix is just sticking to everything.

Anyhow, I can't get the bastard to start now, I've purged the fuel rail 5 times. Suspect it might be a low voltage scenario, nanocom says the batt is only at 11.6V which aint good - probably from all the cranking.

thebiglad · Nov 30, 2014

Bennehboy said:
And this is why the head is being replaced, the oil is coolant contaminated, that's why the head looks so filthy, the oil/coolant mix is just sticking to everything.

Anyhow, I can't get the bastard to start now, I've purged the fuel rail 5 times. Suspect it might be a low voltage scenario, nanocom says the batt is only at 11.6V which aint good - probably from all the cranking.

Battery on charge overnight and try again tomorrow?

Bennehboy · Nov 30, 2014

Jumped it from the wife's car, it lives!

Time for a burn

Bennehboy · Dec 1, 2014

50 miles done today and the coolant is down 1cm - hope this is just the system clearing out air

Mr Noisy · Dec 1, 2014

Lovely that mate.

You're bound to draw some coolant once everything has purged etc

Bennehboy · Dec 1, 2014

Mr Noisy said:
Lovely that mate.

You're bound to draw some coolant once everything has purged etc

Aye hope I'm just being paranoid.

Bennehboy · Dec 2, 2014

Decided I'd see what was coming out the dipstick and oil filler cap, before there was tons of water vapour. Absolutely nothing visible coming out today - although that's at cold start. I'll run it up to temp and check again, but I'm really encouraged!

Bennehboy · Dec 2, 2014

It's blowing some vapour when hot, but it smells like oil not coolant.

Mr Noisy · Dec 2, 2014

td5 always seem to run the coolant lower than the level, but maybe thats just old motors that use it up!

they always seem to level out below the line though!

thebiglad · Dec 2, 2014

Mr Noisy said:
td5 always seem to run the coolant lower than the level, but maybe thats just old motors that use it up!

they always seem to level out below the line though!

I've found that on 2 or 3 of mine. At cold they always settle about 1/2inch below the cold level.

Dave

Bennehboy · Dec 2, 2014

thebiglad said:
I've found that on 2 or 3 of mine. At cold they always settle about 1/2inch below the cold level.

Dave

Yeah quite a few folks have mentioned this but mine always tended to sit wherever I'd left it.

Anyhow I topped it up and went for a 45 minute run at varying work loads (driving miss daisy through to thrashing the arse off it), and the level has stayed at full.

Still not going to say it's sorted though, will give it some time.

Mr Noisy · Dec 2, 2014

Fingers crossed

Bloody td5s!

Less trouble putting fuel in v8s than repairing them 5 pot buggers!

Bennehboy · Dec 2, 2014

Yeah well I don't want to think how much I've spent chasing this issue.

Never again will I be using the place that 'pressure tested' the head.

Maaarrghk · Dec 2, 2014

Glad that you finally have it sorted Ben.

Now go out and play together!

gemsdad · Dec 2, 2014

Bennehboy said:
Yeah well I don't want to think how much I've spent chasing this issue.

Never again will I be using the place that 'pressure tested' the head.

Glad you have finally got it sorted out,at least you have the satisfaction of knowing you have fixed the problem and that you have rebuilt the engine to a high standard,well done.

BennehBoy's D2 adventure

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Coming in your ears.

Well-Known Member

Well-Known Member

Well-Known Member

Coming in your ears.

Well-Known Member

Well-Known Member

Coming in your ears.

Well-Known Member

New Member

NOT BOTHERED.

Similar threads