aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
Erm, Nope, I've already got half of td5 engine in the shed when I don't own a td5 
BennehBoy's D2 adventure
- Thread starter Bennehboy
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Plenty of lube on that hone Benneh and don't go mad with it. Just enough to get rid of any glaze on the bores.
I once did a Honda Sooperdreem with not enough lube and ended up from well within tolerance to just short of re-bore territory. Oops!
Did my FJ1200 a few years back properly and after the hone it was still within factory tolerance for new engines and that was after 80,000 miles.
I once did a Honda Sooperdreem with not enough lube and ended up from well within tolerance to just short of re-bore territory. Oops!
Did my FJ1200 a few years back properly and after the hone it was still within factory tolerance for new engines and that was after 80,000 miles.
Bennehboy
Well-Known Member
- Posts
- 2,215
- Location
- Huddersfield
120000 but no idea how tough it's life had been prior to me buying it at 87K It's had quality oil and filter changes every 6 months to 5000 miles since with me, and I'll be increasing the frequency to every 3 months from now on.
The receipts I got with the car showed the purchase of a head gasket, fitting set and dowels on Jan 12 2010. There's then receipts for a new gasket and a remanufactured head for 25 Jan (from Bridge cylinder heads who I know are a good bunch), so I figure he fitted a new gasket and had the same issue, removed the head and bought the recon unit.
Receipts from the 25th include plastic dowels referenced separately but no sign of head bolts, so wonder if he reused them from the first swap - can't see why he would have bought two HG's if he didn't actually refit the head the first time.
There's a receipt for glow plugs 9 months later, something I'd have swapped with the head - but who knows, cash coulda been tight.
To be fair, I've added a fair amount of performance mods, so the HG failure is probably down to me.
The receipts I got with the car showed the purchase of a head gasket, fitting set and dowels on Jan 12 2010. There's then receipts for a new gasket and a remanufactured head for 25 Jan (from Bridge cylinder heads who I know are a good bunch), so I figure he fitted a new gasket and had the same issue, removed the head and bought the recon unit.
Receipts from the 25th include plastic dowels referenced separately but no sign of head bolts, so wonder if he reused them from the first swap - can't see why he would have bought two HG's if he didn't actually refit the head the first time.
There's a receipt for glow plugs 9 months later, something I'd have swapped with the head - but who knows, cash coulda been tight.
To be fair, I've added a fair amount of performance mods, so the HG failure is probably down to me.
Bennehboy
Well-Known Member
- Posts
- 2,215
- Location
- Huddersfield
Not much done today, had a tool tidy up - they were all over the place - need to get a wheeled cabinet to go under my tool box, just got too much crap these days.
Also gunked the engine bay, bell housing, and ancillaries then jet washed them - looks a lot cleaner but it's hardly going to win any detailing competitions.
Later today should be getting cracked on cleaning the valves and seats, lapping them in, and replacing the stem seals.
Also gunked the engine bay, bell housing, and ancillaries then jet washed them - looks a lot cleaner but it's hardly going to win any detailing competitions.
Later today should be getting cracked on cleaning the valves and seats, lapping them in, and replacing the stem seals.
Bennehboy
Well-Known Member
- Posts
- 2,215
- Location
- Huddersfield
Seats cleaned, there don't appear to be any problems with them...
Valves cleaned, stuck them in a hand drill and got scotchbrited them (padded the collet ends so the jaws wouldn't mark them):
Think if I knew somewhere that could cut them back in well I'd do that rather than lap them, but I don't so they'll just get a very light lapping to avoid turning them concave.
Nearest is probably these in Cas Vegas -> http://www.vintage-engine.net/services.html
Valves cleaned, stuck them in a hand drill and got scotchbrited them (padded the collet ends so the jaws wouldn't mark them):
Think if I knew somewhere that could cut them back in well I'd do that rather than lap them, but I don't so they'll just get a very light lapping to avoid turning them concave.
Nearest is probably these in Cas Vegas -> http://www.vintage-engine.net/services.html
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
Seats cleaned, there don't appear to be any problems with them...
Valves cleaned, stuck them in a hand drill and got scotchbrited them (padded the collet ends so the jaws wouldn't mark them):
Think if I knew somewhere that could cut them back in well I'd do that rather than lap them, but I don't so they'll just get a very light lapping to avoid turning them concave.
Nearest is probably these in Cas Vegas -> Vintage Engines In Elstow Bedfordshire - T & L Engineering
those valves def need lapping in,they are glazed etc,wont take long and you will then know the valves will have good clean seals.
Bennehboy
Well-Known Member
- Posts
- 2,215
- Location
- Huddersfield
Just when I thought there couldn't be any more tedious jobs..... along came valve lapping!
Do these look OK or do I need to go at it longer? The contact area on no 1 exhaust was very small when I started out, so gave it some what for to match it with the rest.
1 & 2:
3 & 4:
5:
Do these look OK or do I need to go at it longer? The contact area on no 1 exhaust was very small when I started out, so gave it some what for to match it with the rest.
1 & 2:
3 & 4:
5:
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
rub valve in clean and dry and if good youll have a thin unbroken shiney line on seat and valve ,valves and seats are usually cut a degree different ie 44 and 45 , modern seat cutters like a serdi need no lapping, depends how yours were done
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
ok,to test each valve.put a TINY drop of clean oil on each valve seat,place it in the head and turn it on revolution backwards then forwards,you should get a complete black line on the valve,if yes then the seat is good,if not re lap it.each to their own though.way i was taught in college.
Bennehboy
Well-Known Member
- Posts
- 2,215
- Location
- Huddersfield
Umm what's clean and dry fella? Google turns up some womens VAG wash lol http://makeupandbeauty.com/clean-dry-intimate-wash-review-2/
I read about different angle cuts, apparently they do this to hammer the faces to the same on first run!!!
Last edited:
Bennehboy
Well-Known Member
- Posts
- 2,215
- Location
- Huddersfield
Bennehboy
Well-Known Member
- Posts
- 2,215
- Location
- Huddersfield
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
seats wiped with solvent ie petrol on a rag
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
that shows it is a complete seal,if not a complete line then seal no good.
Bennehboy
Well-Known Member
- Posts
- 2,215
- Location
- Huddersfield
Ah lol - sorry!
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
paste washed out by oil
