Bankz's 110 Double Cab
- Thread starter bankz5152
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
neilly
Well-Known Member
- Posts
- 20,000
- Location
- Oxfordshireness
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
Mainly because the map is included with the cost of the turbo and id rather have the guy thar supplies the turbo supply the map! Same as if I was going for Allisport or Alive kit.
Just to add there is absolutely nothing wrong with Dynachip, he did my 90 and thats been running like a dream since!
Last edited:
BronkoMini
Active Member
- Posts
- 337
- Location
- Wiltshire
Which turbo are you getting from td5inside?
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
Havnt decided yet, was going to speak to José closer to the time, choose the best one for what I want. From what ive read probs the VNT
BronkoMini
Active Member
- Posts
- 337
- Location
- Wiltshire
Ah fair enough
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
Fitted and balanced! Shockingly only used a tiny amount of weight, at least 4 times less than my 265/75 STTs on Boosts.
Last edited:
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
Got them from 4x4 Tyres
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
Confirmation received! It's being delivered at around 9am tomorrow, I have booked the day off work to get cracking! Got a few bits to fit straight off the bat, like the new alloys/tyres, EGR Blank, RTC Steering Damper and a couple other bits. Also going to remove the turbo heat shield and the acoustic cover (they don't really make bugger all difference). If I have time I may get started on removing the inlet manifold for a bloody good scrub and refit.
Though first thing will be to pull up all the carpet and double check for any rust issues. Didn't find any major signs on inspection when I viewed though doesnt hurt to double check! If there is any it will be sanded down, treated (Fertan), sealed and painted. As well as generally going over the whole thing.
Got it booked in at CSK for Stage 2 Dintrol at a very good price of £250! When I had my 90 done it was £500!
Also provisionally sold the the IFor Williams cover but need something to replace it before I buy the pricey lockable cover... All the tilts and covers seem to be around £300 - £500 which is too much for a 'stop gap' item. So I think I might try and make one. I have some good quality 600D Cordura at home which should be up to the job. Just to keep rain/water off anything I transport in there. Should be able to make for around £40 which would be nice!
So from tomorrow I will have a few bits for sale which I will confirm then/Weds but so far -
Genuine HD Wolf wheels in white with some almost new Insa Sahara tyres fitted
LR 110 Mid-Box
LR Cat/DPF Pipe
Alloy Gearstick and Difflock knobs
Let me know if interested ill put them aside for you.
Though first thing will be to pull up all the carpet and double check for any rust issues. Didn't find any major signs on inspection when I viewed though doesnt hurt to double check! If there is any it will be sanded down, treated (Fertan), sealed and painted. As well as generally going over the whole thing.
Got it booked in at CSK for Stage 2 Dintrol at a very good price of £250! When I had my 90 done it was £500!
Also provisionally sold the the IFor Williams cover but need something to replace it before I buy the pricey lockable cover... All the tilts and covers seem to be around £300 - £500 which is too much for a 'stop gap' item. So I think I might try and make one. I have some good quality 600D Cordura at home which should be up to the job. Just to keep rain/water off anything I transport in there. Should be able to make for around £40 which would be nice!
So from tomorrow I will have a few bits for sale which I will confirm then/Weds but so far -
Genuine HD Wolf wheels in white with some almost new Insa Sahara tyres fitted
LR 110 Mid-Box
LR Cat/DPF Pipe
Alloy Gearstick and Difflock knobs
Let me know if interested ill put them aside for you.
Last edited:
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
They are too narrow. Cooper state that these tyres should only be fitted to a minimum of a 7.5" wheel. The Wolfs are 6.5" i believe where as my Bowlers are 8" so ideal.
Arierep
Active Member
- Posts
- 127
Yes, no question they are outside most manufacturers recommendations, is just that plenty of guys run them that way with good results. Also, the narrow rim retains the bead quite well.
Anyway, what matters the most in this cases is not tyre width, but actually the angle the bead enters the rim. This is a combination of tyre width but aso sidewall height.
In my geekness, I once made a table that gives an aproxímate bead angle for most common LR rim widths and tyre sizes. Considering most tyre manufacturers specs, an angle between 10 to 12º might be ideal, but up to about 16º is also possible:
Anyway, what matters the most in this cases is not tyre width, but actually the angle the bead enters the rim. This is a combination of tyre width but aso sidewall height.
In my geekness, I once made a table that gives an aproxímate bead angle for most common LR rim widths and tyre sizes. Considering most tyre manufacturers specs, an angle between 10 to 12º might be ideal, but up to about 16º is also possible:
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
Hmmm!! Thats pretty useful!
Tbh I was always going to buy the Bowlers, just not right now is all.
In other news it has arrived!! Well at 9am this morning but ive been doing stuff to it
CHUNKY! Except me bloody wheel nuts havnt arrived!
That sexy XS interior
Clutch spring mod done -
Second one ive done and everytime i smash a knuckle and it kills!! Worth it though 10x easier to drive.
Only thing ive noticed is that the difflock light isnt coming on? Any ideas?
Far as I can tell the difflock works, jacked up front wheel, spins - difflock off.
Diffllock on - no spin
Tbh I was always going to buy the Bowlers, just not right now is all.
In other news it has arrived!! Well at 9am this morning but ive been doing stuff to it
CHUNKY! Except me bloody wheel nuts havnt arrived!
That sexy XS interior
Clutch spring mod done -
Second one ive done and everytime i smash a knuckle and it kills!! Worth it though 10x easier to drive.
Only thing ive noticed is that the difflock light isnt coming on? Any ideas?
Far as I can tell the difflock works, jacked up front wheel, spins - difflock off.
Diffllock on - no spin
Last edited:
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
I will do that today for you, got to find the bloody tape measure!
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
They are approx 32.5" tall
