Bankz's 110 Double Cab

dieseldog69 · May 22, 2018

Be happy it's not a D1, the chassis mounts are part of the tubular chassis crossmember and you can't remove them, I cut through mine with a 1mm slitting disc and happy days.

It's not a terrible job unless it doesn't play nicely then it's a proper PITA!

bankz5152 · May 22, 2018

neilly said:
As said, my bracket bolts just popped out......LOL.

Good job jobbed there me old china. Not nice to do when a PITA , but nice to get the job done.

Cheers

Took me 2 hours on my 90! I though yeah this wont take long, few hours then a nice pub lunch in the sun! 2 days later and it was a pub dinner

lol

Glad its done though! Fair bit of the tranny slop/backlash is gone now so thats good!

bankz5152 · May 24, 2018

Finally got around to getting the A/C looked at properly. Apparently no leaks... held vacuum so all good there. Got UV dye in it so shall keep an eye on for thr next couple weeks. Hopefully it holds.

Regassed and working well. Compressor clutch kicks in now so that is good!

The fan on the AC condensor doesnt spin though? Should it? Its no seized and does work when tested on the Nanocom.

bankz5152 · May 25, 2018

New CB fitted. Got sick of the old one so nice new Maxon CM70 installed inside the cubby for ease.

bankz5152 · May 25, 2018

New D44 bumper arrived! Ready for some FXLiner

dieseldog69 · May 26, 2018

bankz5152 said:
New D44 bumper arrived! Ready for some FXLiner

View attachment 149738

That looks a tasty bit of kit

bankz5152 · May 28, 2018

Finally got around to painting it...

Two full coats of Buzzwelds 2K FXLiner sprayed on! Meant to be as tough as nails. Similar to Raptor but a finer texture. Kinda like find sand paper. I really like it.

Can kind of see the texture

bankz5152 · May 29, 2018

Been bored so decided to make some seat risers/leg room extenders

Only had one bit but thought id try it out before I bought some more sq section. Came out pretty well! I havnt infact got almost too much leg room, properly have to reach for the gear stick

Moves the whole seat back around 1" and raises it up 30mm, not too noticeable but loads of room!

So ive ordered two lengths of 600mm 30x30x2mm sq section, some nice 16mm M8 socket heads and some end caps - Undecided if I want end caps ot the 45 degree cut I did in the pic above. Will extend them a little so the bolts have some more meat around them.

Not bad i think! Should only cost me around £12 and an hour of my time. Not £150 from Exmoor

Ill spray em up in CIO when ive made the proper ones.

Hicap phill · May 29, 2018

You could Use cap heads & Allen keys for the lower rail. You can then cut this square & end cap it.

bankz5152 · May 29, 2018

Yeah I've ordered some to see! I quite like the look of the 45 but the endcaps may look better.

KISSMYAURA · May 29, 2018

bankz5152 said:
Yeah I've ordered some to see! I quite like the look of the 45 but the endcaps may look better.

Fit endcaps to the 45?

Get a scalpel set from Hobby craft & and a pack of plasters depending on your beer intake or general 'oaf index'
I myself have an oaf index of 4 oddly cider seems to triple it....

PS how about a box sec 'U' shape sleeve in plaaarstic or meytal?

bankz5152 · May 29, 2018

Decent idea that! Roughly the same oaf index

"PS how about a box sec 'U' shape sleeve in plaaarstic or meytal?" What do you mean by this?

KISSMYAURA · May 29, 2018

bankz5152 said:
Decent idea that! Roughly the same oaf index

"PS how about a box sec 'U' shape sleeve in plaaarstic or meytal?" What do you mean by this?

Sorry still enjoying my BH and a bottle of aspalls!

So instead of square box section get a bit slightly bigger but 'U' so it will slide over the box sec you have in situ, weld a metal end to it polish and voila no caps smooth and sleek, just a thought........ like this pic

OR Could always weld on end to your square box sec and drill hole in top or the side under seat and fit a round rubber bung etc

i seem to be obsessed with hiding access fixing holes at the mo, must the kitchen i have just fitted at home....

KISSMYAURA · May 29, 2018

Or could look tasty in SS 'box in tube' as over sleeves.

bankz5152 · May 29, 2018

That is quite a fancy solution!

KISSMYAURA · May 29, 2018

bankz5152 said:
Been bored so decided to make some seat risers/leg room extenders

Only had one bit but thought id try it out before I bought some more sq section. Came out pretty well! I havnt infact got almost too much leg room, properly have to reach for the gear stick

Moves the whole seat back around 1" and raises it up 30mm, not too noticeable but loads of room!

View attachment 150089

So ive ordered two lengths of 600mm 30x30x2mm sq section, some nice 16mm M8 socket heads and some end caps - Undecided if I want end caps ot the 45 degree cut I did in the pic above. Will extend them a little so the bolts have some more meat around them.

Not bad i think! Should only cost me around £12 and an hour of my time. Not £150 from Exmoor

Ill spray em up in CIO when ive made the proper ones.

Like yer work here! maybe box in the lot with a bit of stainless?

bankz5152 · May 29, 2018

KISSMYAURA said:
Like yer work here! maybe box in the lot with a bit of stainless?

Youre making what was a cheap idea when bored expensive

Hahaha i may consider making in fancy in the future for now im happy with the leg room ill gain when i make em properly next week!

KISSMYAURA · May 29, 2018

lol, yep i tend to do that

KISSMYAURA · May 29, 2018

bankz5152 said:
Youre making what was a cheap idea when bored expensive

Hahaha i may consider making in fancy in the future for now im happy with the leg room ill gain when i make em properly next week!

My 90 hard top has the cross member, I am over 6ft and need to remove it etc.

I look like a T-rex in a phone box as it is when I am driving me tratter

bankz5152 · May 29, 2018

Hahaha thats exactly how I was in my 90 lol

Bankz's 110 Double Cab

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Attachments

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads