Axle Stands

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
There have been recalls on a number of stands *similar* in design to those, above. Broken welds. broken locks, cracks on folds etc.

I have 4 big iron base mothers, from probably the 50's or 60's. Huge threaded shaft and a spinny wheel-nut thing to adjust them.

Apparently you can still buy similar, as "Dawn" brand from Aus... though mine are a different brand:

1706000937066.jpeg
 
AllanWorms said:
There have been recalls on a number of stands *similar* in design to those, above. Broken welds. broken locks, cracks on folds etc.

I have 4 big iron base mothers, from probably the 50's or 60's. Huge threaded shaft and a spinny wheel-nut thing to adjust them.

Apparently you can still buy similar, as "Dawn" brand from Aus... though mine are a different brand:

View attachment 308515
Click to expand...
looks scary, not something i would trust with my life
 
RustyDefender said:
Unless i'm using a 2 post ramp, anytime i throw axel stands under it i leave the jack under there after i drop it on the axel stands.. i just put jack it back up (ever so slightly) to where they're on axel stands just incase they fail i've got a fall back
Click to expand...
I have a trolley jack and only lower the vehicle onto the stands, I always leave the jack underneath as a just in case and usually thrown the wheel under the cill so if all else fails and it it all goes pete tong at least there will be some gap between the ground and the vehicle.
Then as I get older I have got more paranoid, no less.
 
dag019 said:
Definitely cheating!

also is that a sticker on the truck top of did you miss the fork the first time and punch a hole :p
Click to expand...
No I don’t think so. I think it was an ifor Williams sticker. I’d just been given the Land Rover so I was being extra careful 🤣
 
backinblack said:
This better :)

View attachment 308547
Click to expand...
I'm not sure, those you have added look distinctly DIY and reading through this thread people seem to disagree with DIY stands!

also looking more closely at the picture I thought @Def90man said he was never underneath it in that position but I can definitely see a little pile of spanners underneath the middle of the vehicle :rolleyes:
 
dag019 said:
I'm not sure, those you have added look distinctly DIY and reading through this thread people seem to disagree with DIY stands!

also looking more closely at the picture I thought @Def90man said he was never underneath it in that position but I can definitely see a little pile of spanners underneath the middle of the vehicle :rolleyes:
Click to expand...
It's ok I've been and bought some :)

1706033780667.png
 
dag019 said:
I'm not sure, those you have added look distinctly DIY and reading through this thread people seem to disagree with DIY stands!

also looking more closely at the picture I thought @Def90man said he was never underneath it in that position but I can definitely see a little pile of spanners underneath the middle of the vehicle :rolleyes:
Click to expand...
Believe it or not I had to go underneath and unbolt everything before lifting her arse up and rolling the axle out 😛
 
I think the debate is interesting.

Yes, you can buy them cheaper than making them. In this case, as stated earlier, I was looking for plans/drawings for axles stands so I could make my own. It is the fabrication of them that interests me and asking for drawings so that I avoided some of the issues mentioned here to ensure safety. Not some drawing someone has hashed up on a fag packet.

I have no intention of working under a vehicle with ropey stands or jacks, even forklifts as I've seen them fail and the damage done.

The picture Lynall posted, I have four of that type and have never trusted them, so much so I used blocks with them "just in case".
 
Tirran said:
The picture Lynall posted, I have four of that type and have never trusted them, so much so I used blocks with them "just in case".
Click to expand...
this style is the same as the ones that I use and I trust them completely, however as stated in an earlier post I have a set of oversized ones for a land rover. Mine are I belive an 8 ton pair so each stand is rated at 4 ton, which is more than the complete weight of the 110 let alone only half the vehicle that is supported at any time (i have never needed to have all four wheels off it at the same point) I also do as mentioned earlier in this thread the leave the jack under as extra support.

I am not against diy fabrication (i just don't think axle stands are worth the effort) the set of ramps that I have are a DIY job from an old boy who used to work on military trucks. Just a selection of 6mm flat strap welded together onto a 6mm angle iron fame, but again I use them with confidence on the same premise as my axle stands. If they supported armoured HGVs they will support a land rover with no issue at all.
 
You must log in or register to reply here.

Similar threads

C
Axle Stands
Replies
8
Views
747
GrumpyGel
GrumpyGel
suew
Rear Axle Oil Leak
Replies
6
Views
685
suew
suew
dag019
LT77 clicking loudly in 5th gear
Replies
7
Views
997
Skolmate
Skolmate
ER1C
For Sale CAR RAMPS [sold]
Replies
0
Views
609
ER1C
ER1C
proto57
Freelander 2 (LR2) Baffling (to me!) front Half-shaft/Axle Length Mystery! Too short, twice???
Replies
10
Views
1K
Zorro587
Zorro587
Back
Top