At the back of the shed was a series 1
- Thread starter Suffolkseries
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Suffolkseries
Member
- Posts
- 10
- Location
- Suffolk
That's a good idea but it might make
Take some pics of the unearthing and starting process and start a thread of the old girl being brought back to life
Welcome
Sounds like you have found a little gem.
for better advise/coverage of the gurus you could ask in here.
https://www.landyzone.co.uk/forum/defender-90-110-130.7/
or here
https://www.landyzone.co.uk/forum/series-land-rovers.6/
But would be great to see some pics.
Hope you are trailering it?
the fuel may smell good but get rid of it. Basically drain and change everything fluid ( personally)
good luck with your new family addiction
J
Suffolkseries
Member
- Posts
- 10
- Location
- Suffolk
Hi guys,
We have some life! We turned her over with the starter motor with no problem. The radiator was not leaking, the oil came out clean.
Headlights came on
We just dont have a key and I am not sure how to start it without one.
Does anyone know how to start it or where to get a key from ?
We have some life! We turned her over with the starter motor with no problem. The radiator was not leaking, the oil came out clean.
Headlights came on
We just dont have a key and I am not sure how to start it without one.
Does anyone know how to start it or where to get a key from ?
Suffolkseries
Member
- Posts
- 10
- Location
- Suffolk
- Posts
- 33,601
- Location
- North Shropshire
You can try another key of the right size, jiggle it about a bit and it might work but be very gentle
swisstoe
Well-Known Member
- Posts
- 655
- Location
- Lancashire
If you cant find a suitable single sided key, you can put a direct 12v to the coil and bridge the solenoid.
You may find the solenoid has a red starter button already...
You may find the solenoid has a red starter button already...
- Posts
- 13,787
- Location
- The Principality
It's me and I can give you an idea that might be of no use whatsoever but then .....it might be!
I use a plastic-type material which comes in the form of tiny 'baubles' which, when put in boiling water, melts into a mass. This can then be pressed into any shape and then it hardens completely and does not stick to anything you are trying to make the mould of. If it is not right, you can simply re-melt it and try again. I use it for making faux water, waterfalls etc. when making models. When hot it is clear but when cold it is opaque. It could give you an idea of what pattern is needed to make/buy a new key!
Now I can almost hear the comments so I'm off before I get chased!!!!
I use a plastic-type material which comes in the form of tiny 'baubles' which, when put in boiling water, melts into a mass. This can then be pressed into any shape and then it hardens completely and does not stick to anything you are trying to make the mould of. If it is not right, you can simply re-melt it and try again. I use it for making faux water, waterfalls etc. when making models. When hot it is clear but when cold it is opaque. It could give you an idea of what pattern is needed to make/buy a new key!
Now I can almost hear the comments so I'm off before I get chased!!!!
Hicap phill
Well-Known Member
- Posts
- 16,249
- Location
- Wiltshire
+1 on find the starter solinoid.that key ignition only turns the power on. There will be a button somewhere which is press to start.(look under the speedo housing)
The outer of that ignition is the side/head lights.
Find a link to the series 1 club who may be able to help with a key(that visible number is the key cut code)
The outer of that ignition is the side/head lights.
Find a link to the series 1 club who may be able to help with a key(that visible number is the key cut code)
- Posts
- 33,601
- Location
- North Shropshire
An old tractor will likely have the same key type of you need a cheap blank
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
Tractors of that vintage have incredibly simple keys, if any at all, a switch sufficed for many.
I would be looking S1 club, as above^^^^^^^, or else a cheap British car blank of the same period, Morris Minor, Hillman or similar.
Hicap phill
Well-Known Member
- Posts
- 16,249
- Location
- Wiltshire
Key should look like this.
Take some photos of the dash & other buttons you are not sure of.
Take some photos of the dash & other buttons you are not sure of.
Hicap phill
Well-Known Member
- Posts
- 16,249
- Location
- Wiltshire
Also Before jump starring &playing with the electrics check to see if it’s a positive earthed motor
freelance
Well-Known Member
- Posts
- 8,686
- Location
- essex and beyond
My old mans rover 2000 had the same no. key, probably still have it somewhere
NorfolkBird
Well-Known Member
- Posts
- 17,699
I've got a bunch of keys found under the seatbox in my series. Let me know if you don't have any luck.
