David Leech
Well-Known Member
- Posts
- 302
- Location
- Galway, Ireland
Got myself a 1979 Series 88". Most of the parts seem to be there, bar the.....engine!
A Serious Project
- Thread starter David Leech
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
David Leech
Well-Known Member
- Posts
- 302
- Location
- Galway, Ireland
It's an Irish registered Series and came with the original Brown Tax Book.....
FlyingPete
Well-Known Member
- Posts
- 1,305
- Location
- Coventry
Should be a good project! What engine are you putting in it?
rob1miles
Well-Known Member
- Posts
- 3,565
- Location
- Slough and Bath
Perfect for a DIY electric conversion, I was thinking of doing the same if an engineless series came up. Better than argueing about 200TDIs or V8*s, It will be exempt just about everything and spont on the latest trends. Forklift motor onto the transfer case to give 2 speeds and loads of capcity for the battery weight.
https://www.lro.com/reviews/featured-vehicles/1409/electric-series-i
https://www.lro.com/reviews/featured-vehicles/1409/electric-series-i
David Leech
Well-Known Member
- Posts
- 302
- Location
- Galway, Ireland
The 'Good Bits' are that it's almost all there, nothing had been robbed from it over the years. The 'Bad Bits' are the usual stuff, the front and back crossmembers are rotted beyond repair. The two main chassis rails are in surprisingly good order. The two front outriggers are scrap. Footwells need attention, and top hinge area of bulkhead.
Bonnet skin is good but the framework is dust, can lengths of this be bought or do I have to try 'fabricate' something myself?
A bad gash at the rear.....
And this piece, on passenger side, behind front spring hanger is bad. I don't know if anything needs to attach to it though, is it needed for the engine?.....
Bonnet skin is good but the framework is dust, can lengths of this be bought or do I have to try 'fabricate' something myself?
A bad gash at the rear.....
And this piece, on passenger side, behind front spring hanger is bad. I don't know if anything needs to attach to it though, is it needed for the engine?.....
Last edited:
David Leech
Well-Known Member
- Posts
- 302
- Location
- Galway, Ireland
I'm hoping to source a 200Tdi and squeeze it in, but am in no rush to do so, there's enough to be doing to try and get the chassis back to usable condition. I'll just plod along and keep on the lookout for a 'handy' engine.....
FlyingPete
Well-Known Member
- Posts
- 1,305
- Location
- Coventry
Always a good (if noisy) option if you can find one that's in a good condition. 200tdi are all quite old now and it's probably worth overhauling it before you put it in the car.
Was the car petrol or diesel originally? If petrol, a Defender 2.5 petrol with a few modifications would be a good swap. They are fairly detuned to run on poor-quality fuel as standard.
Phil Gibbs
Active Member
- Posts
- 119
- Location
- Nuneaton
Good luck
JimS
Well-Known Member
- Posts
- 10,733
- Location
- Not far enough away from London
Looks like it'll keep you busy for a while. Take your time and enjoy
David Leech
Well-Known Member
- Posts
- 302
- Location
- Galway, Ireland
Thanks for that, I'll prob just cut it away so.....
David Leech
Well-Known Member
- Posts
- 302
- Location
- Galway, Ireland
Registered as Diesel.....
FlyingPete
Well-Known Member
- Posts
- 1,305
- Location
- Coventry
Easier to stick with diesel then, though converting to petrol isn't that difficult to do. Nowadays I don't think it's worth going from petrol to diesel anymore.
If you're doing chassis repairs anyway, it wouldn't be much extra work to move/modify engine mounts if you needed to. Then your options increase to whatever will physically fit. If you can find one and get it working, 2.0mpi from a Discovery would be a great engine for it.
rob1miles
Well-Known Member
- Posts
- 3,565
- Location
- Slough and Bath
Look forward, go electric! I'll bet it adds more valaue too.
