P38A A series of faults

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Wheel bearing done:

W6wJvog.jpg


xjnxqk0.jpg


Relented and slotted the shroud for the ABS sensor just in case

Used my ebay special bush/bearing puller, which uses an M14 bolt, to press the hub into the bearing centres and it all went together like butter with the aid of some ACF50 anti-corrosion 'oil' as lube

Need to get the hub off still to replace the bottom ball joint (having a right old battle with none of the right joint splitter tools) and will resort to attacking it with a slitting disc soon...

Also have to replace the CV gaiter which is the reason this hub was coming apart in the first place
 
Swivel housing now off the axle care of my angle grinder and a cutting disc. Naturally in cutting through the old lower ball joint shaft it freed the taper off that I had so unsuccessfully been doing battle with :rolleyes:

Have got the old ball joint insert starting to shift in the axle, but need something beefier than a big G cramp really, and I can't get my 10t gear puller on to it with the floppy legs obaying gravity more than they will me...I need to explore my big bits of metal pile to see if I can adapt something
 
Slooby said:
Swivel housing now off the axle care of my angle grinder and a cutting disc. Naturally in cutting through the old lower ball joint shaft it freed the taper off that I had so unsuccessfully been doing battle with :rolleyes:

Have got the old ball joint insert starting to shift in the axle, but need something beefier than a big G cramp really, and I can't get my 10t gear puller on to it with the floppy legs obaying gravity more than they will me...I need to explore my big bits of metal pile to see if I can adapt something
Click to expand...
Got a lass in local pub with big bits:rolleyes::rolleyes::D
 
Before I attempt to modify a G clamp into a ball joint press, or buy one, does anyone around the Tonbridge or Basingstoke areas happen to have one I could possibly borrow?

In other news I've ordered a 10 litre Ultrasonic cleaning tank in an effort to clean out all the gloop and carbon from my turbo housings and inducer/exducer wheels. It's hold also be big enough to take the transmission cooler which is utterly caked in oil soaked mud.
 
Slooby said:
Before I attempt to modify a G clamp into a ball joint press, or buy one, does anyone around the Tonbridge or Basingstoke areas happen to have one I could possibly borrow?

In other news I've ordered a 10 litre Ultrasonic cleaning tank in an effort to clean out all the gloop and carbon from my turbo housings and inducer/exducer wheels. It's hold also be big enough to take the transmission cooler which is utterly caked in oil soaked mud.
Click to expand...

@tomcat59alan posted a link to a kit on eBay for about £50.
 
Yeah, I could buy one of the 10 piece kits for about 30 quid or 50 for the 21 piece, but I'm rather throwing too much money around at the moment and need to kerb my spending...
The G cramp I was using was starting to make things move, but I really need to get a better lever onto it to really get the forces up than relying on the rather bendy 'pin handle'. I was going to weld on an old flanged hub nut I've found kicking around, or look at making something that my gear puller could attach to without the legs flopping about
 
brianp38dse said:
Did you warm up the hub and put the ball joint in the freezer over night as that helps.
Click to expand...

I don't fancy my chances of getting the axle in the freezer ;) It was the getting the old ball joint out that had been the problem...the new ones will be going in the freezer though as every micron helps when putting them back together

I say had as I've got both top and bottom joints out now, welding an old hub nut onto the G cramp only succeeded in me breaking the clamp's swivel foot off the screw :oops: However I did find a way to use my hydraulic gear puller in the end and using the remains of some old bearing races I was able to press out both ball joints. I ended up having to remove tge top one as well after finding it's gaiter was also split and there being virtually no grease left in it.

I'll order up a top ball joint in a bit, but will need to discover a suitable diameter press tube in something to press it in
 
Well rebuilding the turbo was a complete waste of time

Just snapped the impellor shaft applying a massive 8 Nm of torque while finishing off the rebuild.

Currently of a mind to set the whole fesking pile on fire :mad:
 
A new CHRA (core) looks to be around £150 quid for a decent branded replacement, meanwhile a second hand turbo about £60 delivered, which I could just swap the wheels and shaft from into my freshly rebuilt core...and tighten the bloody nut with a lot more care
 
Cold light of day has revealed how I managed to snap the shaft; it turns out that my 5-25Nm Teng Torque wrench only works as a torque wrench on a clockwise rotation, anti-clockwise locks it :mad:
 
You must log in or register to reply here.

Similar threads

K
Is my RR Classic in EAS shutdown?
Replies
12
Views
1K
kevleaper
K
M
Whats happened to Storey Wilson RSW Solutions
Replies
5
Views
490
mousemat
M
O
03 L322 EAS ECU Can bus fault / ABS temp system deactivation
Replies
1
Views
780
oldradiotech
O
Montyjohn
P38A Adding a valve to manually fill EAS tank and why did my pump fail again?
Replies
14
Views
1K
Datatek
Datatek
Montyjohn
P38A A couple of queries about rebuild EAS valve block
Replies
9
Views
911
Grrrrrr
Grrrrrr
Back
Top